background image

1/3 

 
- Preface 

Thank you for purchasing a Yamada Pump. 
The SR-140 / 125DAL series is air operated pump units designed for use with a drum (

Refer to “6.Specifications”

). With a 

combination of a type 140 / 125 air powered pump and an air operated lift, the unit is suitable for transferring/supplying high 
viscosity materials like grease. 
Through pipes and hoses, material can be supplied to various sections of a work site. At each section, you can use material 
anytime just by controlling an outlet valve. 
The inductor plate provides a tight seal between the plate and a drum, prevents an air pocket from forming in the suction port, 
and helps to pump and transfer material efficiently until a drum gets empty. 
Furthermore, a punch plate attached to the bottom of the inductor plate makes it possible to use up material in a drum as 
much as possible. 
 

-  For Safe Operation 

This document describes the items that are important for the user to operate this product safety, correctly, and efficiently. 
Before operating this product, read this manual thoroughly, in particular, “Warnings and Cautions” at the beginning of this 
manual, with a good understanding of its contents. Keep this manual carefully in an easy-to-access place so that the user 
may refer to it whenever necessary. 
 

-  Warnings and Cautions 

To use this product safely, be sure to observe the contents of the following description. In this manual, warnings and cautions 
are indicated by using symbols. These symbols are intended to prevent death or serious injury that may be caused to the 
operator or those who are around the product and damage that may be caused to the articles that are around the product, as 
well as to use the product safely and correctly. Each symbol is indicated and has a meaning as shown below. Read the 
description with a good understanding of its contents. 
 

WARNING :

 

This indicates the existence of potential hazard which, if not avoided, will result in 

death or serious injury. 

CAUTION : 

This indicates the existence of potential hazard which, if not avoided, may result in 

bodily injury or in physical damage. 

To indicate the contents of danger and damage, the following symbols are used together with the above indications. 

 

This symbol indicates an act that is prohibited (prohibition). The concrete contents of prohibition are indicated 
by the side of the indication. 

 

This symbol indicates the contents that must be observed. The concrete contents of observance are indicated 
by the side of the indication. 

 
 

Summary of Contents for 140 Series

























Reviews: