background image

Studer Innotec SA 

Xtender

 

User manual 

V4.6.0 

40 

 

Indicated alarm

 

Comment

 

1x 

(Imminent) stoppage due 
to a too low battery 
voltage. 

If the inverter has not yet stopped, it is recommended to 
disconnect all non-priority loads and/or start up the generator. If 
the inverter has stopped, it will restart automatically when the 
battery voltage has reached the correct value again {1110}. It 
can be restarted manually using the ON/OFF button (41) as long 
as the battery voltage is higher than 1,5V/cell. The charger 
remains functional as long as the battery voltage remains higher 
than 1,5V/cell.  See also sect. 7.4 – p. 30. 

2x 

Stoppage due to 
overload in the 
equipment, due to either 
a short-circuit or too high 
load for the inverter. 

In this event, the equipment will attempt to restart 3 times within 
a few seconds and will stop if the overload remains (see sect. 
7.4.1 – p. 30). It is vital to eliminate the cause of the overload 
before restarting. Restarting is carried out manually by pressing 
the button (41).  

3x 

Decrease in the rated 
output of the device due 
to a too high internal 
temperature.  

This may be due to overload of the device, too high ambient 
temperature or obstructed ventilation. The power output of the 
device will therefore be limited to around 50% of the Pnom, 
including in charger mode or Smart Boost mode.  

4x 

Battery voltage higher 
than the maximum limit 
set by the parameter 
{1121}. 

Check the cause of this excess voltage. The equipment will 
restart automatically when the voltage falls below the threshold 
value {1122}.  
See sect. 7.4.2 – p. 30. 

5x 

No transfer. Insufficient 
power from the source 

In this case, the Xtender remains in operation in inverter mode 
until the output power decrease below the input limit and does 
not allow the transfer relay to close. You must increase the input 
current limit {1107}, authorise exceeding this limit {1436}, authorise 
backup on the source {1126}, or disconnect some consumers 
(decrease of loads). 

6x 

Start-up prevented due to 
unwanted voltage at the 
device output. 

Voltage is present at the device output. Check your cabling: 
correct the fault and start the installation again using a manual 
control on the button (41). 

7x 

Indicates missing voltage 
in one of the units of the 
system in a multi-unit 
configuration. 

Check the input protection devices (H) for all the system units.  

8x 

Software incompatibility 
in a multi-units system 

Error in a multi-Xtender system. The LED 43 gives further 
information: 
3x: Communication protocol error or  
4x: Software incompatibility 
The software version of all units in the system must be the same. 
Proceed according to the RCC-02/-03 user manual to upgrade 
the software. 
5x: communication loss or functional error: check the 
terminations on the communication bus and make a reset of the 
system {1468}  

9x 

Loss of synchronization 
between the units 

Failure of the link between the units. Check the presence and 
the state of the communication cables between units. 

 

(

43)

 This indicator is glowing continuously when the device is working.  

It flashes when the equipment is temporarily stopped due to a fault displayed by the indicator (42) 
or a ON/OFF control wired at the remote entry ("Remote ON/OFF") (7), or when the equipment is put 
to idle mode by the master unit in a multi-inverter parallel system (see sect. 8.2 - p. 34). 
 

 

The  equipment  will  restart  automatically  when  the  conditions  that  led  to  the  temporary 
stoppage have gone away. 

In  the  systems  with  multi-units  in  parallel,  the  indicator  (43)  blinks  2  times  when  the  Xtender  is 
temporarily stopped by the master unit of the concerned phase while this mode is authorized. {1547}. 

Summary of Contents for XTS 900-12

























































Reviews: