manualshive.com logo in svg

Xtender XTS 900-12, User Manual

Share
Download
Xtender XTS 900-12 User Manual Download Page 44

Studer Innotec SA 

Xtender

 

User manual 

V4.6.0 

44 

16

 

DRAWING ELEMENTS (DC SIDE) 

Elem.  Description 

Comment 

a 

RCC-02/-03 

remote 

control 

This  device  allows  complete  configuration  of  the  installation  as  well  as 
displaying the system behaviour. It is recommended but not necessary for 
the installation to function well. See sect. 9.1 – p. 35. 

b 

Battery 

The battery capacity is constituted according to figures 5a to 6d based on 
the required voltage. Note: It is vital that the voltage and the polarity of the 
battery  be  checked  before  connecting  to  the  inverter.  An  overload  or 
incorrect polarity could seriously damage the Xtender. Correct dimensioning 
of the batteries is essential for trouble free operation of the system. See sect. 
4.3.1 – p. 18. 

c

 

Earthing 

See sect. 4.5.5 – p. 22 

e 

Communicati

ons cable 

Communications cable. Only an original cable supplied by Studer Innotec 
may  be  used.  The  total  length  of  the  communications  cable  must  not 
exceed 100 m for 3 x RCC-02/-03 or 300 m for a single RCC-02/-03. 

f 

Protection 

devices 

A  fuse-type  device,  thermal  circuit  breaker  or  magnetic-thermal  circuit 
breaker  (see  fig.  8a)  must  be  installed  on  at  least  one  of  the  two  battery 
conductors. It will ideally be placed on the positive pole of the battery and 
as close as possible to this. The calibre of the device is selected according 
to the cable cross-section used.  
If the negative pole of the battery is not earthed, it must also be protected 
by such a device. 

h 

Distribution 

bar 

Positive pole of the battery 

j 

Distribution 

bar 

Negative pole of the battery 

k 

Wind-

powered 

or/and 

micro-hydro  

generator 

One or more wind-powered generators or/and micro-hydro with their own 
regulation  system  may  be  used  to  directly  charge  the  battery.  Its 
dimensioning does not depend on the Xtender and does not interfere with 
it. 

m 

Solar 

generator 

One or more solar-powered generators with their own regulation system may 
be used to directly charge the battery. Its dimensioning does not depend 
on the Xtender and does not interfere with it. 

r 

Remote entry  

A control device may be connected to the terminals (7) of the Xtender. See 
sect.  7.7  –  p.  31.  On  XTM  and  XTS  this  input  is  available  on  a  separate 
(external) device RCM-10 (see sect. 9.3.1- p. 36). 
 

t 

BTS-01 

temperature 

sensor 

The  sensor  is  placed  in  the  immediate  proximity  to  the  battery.  If  the 
installation comprises several Xtenders, a single sensor is connected to one 
of the units. See sect. 9.2 - p. 36. 

 

 

 

Summary of Contents for XTS 900-12

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands