Xilinx Virtex-5 RocketIO GTP User Manual Download Page 29 | Manualshive

Page: 29 / 316

background image

Virtex-5 RocketIO GTP Transceiver User Guide

29

UG196 (v1.3) May 25, 2007

Ports and Attributes

R

RXSTATUS0[2:0]

RXSTATUS1[2:0]

Out

RXUSRCLK2

Shows status of PCI Express or SATA
operations. The decoding depends on
the setting of RX_STATUS_FMT.

TX OOB/Beacon
Signaling

OOB/Beacon Signaling

Receive Detect Support

RXUSRCLK20

RXUSRCLK21

In

N/A

Input clock used for the interface
between the FPGA and the GTP
transceiver.

FPGA RX Interface

RXUSRCLK0

RXUSRCLK1

In

N/A

Input clock used for internal RX logic
after the RX FIFO.

FPGA RX Interface

RXVALID0

RXVALID1

Out

RXUSRCLK2

Indicates symbol lock and valid data on
RXDATA and RXCHARISK[1:0] for
PCI Express.

RX OOB/Beacon
Signaling

TXBUFDIFFCTRL0[2:0]
TXBUFDIFFCTRL1[2:0]

In

Async

Controls the strength of the TX pre-
drivers. Tie this port to the same value
as TXDIFFCTRL.

Configurable TX Driver

TXBUFSTATUS0[1:0]

TXBUFSTATUS1[1:0]

Out

TXUSRCLK2

TX buffer status. Indicates TX buffer
overflow or underflow.

TX Buffering, Phase
Alignment, and Buffer
Bypass

TXBYPASS8B10B0[1:0]

TXBYPASS8B10B1[1:0]

In

TXUSRCLK2

Controls the operation of the TX
8B/10B encoder on a per-byte basis.

Configurable 8B/10B
Encoder

TXCHARDISPMODE0[1:0]

TXCHARDISPMODE1[1:0]

In

TXUSRCLK2

TXCHARDISPMODE and
TXCHARDISPVAL allow the 8B/10B
disparity of outgoing data to be
controlled when 8B/10B encoding is
enabled. When 8B/10B encoding is
disabled, TXCHARDISPMODE is used
to extend the data bus for TX interfaces
whose width is a multiple of 10.

Configurable 8B/10B
Encoder

TXCHARDISPVAL0[1:0]

TXCHARDISPVAL1[1:0]

In

TXUSRCLK2

TXCHARDISPVAL and
TXCHARDISPMODE allow the
disparity of outgoing data to be
controlled when 8B/10B encoding is
enabled. When 8B/10B encoding is
disabled, TXCHARDISPVAL is used to
extend the data bus for 10- and 20-bit
TX interfaces.

Configurable 8B/10B
Encoder

TXCHARISK0[1:0]

TXCHARISK1[1:0]

In

TXUSRCLK2

Set High to send TXDATA as an
8B/10B K character.

Configurable 8B/10B
Encoder

TXCOMSTART0

TXCOMSTART1

In

TXUSRCLK2

Initiates the transmission of the COM
sequence selected by TXCOMTYPE
(SATA only).

TX OOB/Beacon
Signaling

TXCOMTYPE0

TXCOMTYPE1

In

TXUSRCLK2

Selects the type of COM signal to send
(SATA only).

TX OOB/Beacon
Signaling

Table 1-3:

GTP_DUAL Port Summary

(Continued)

Port

Dir

Domain

Description

Section (Page)

«
...
27
28
29
30
31
...
»

Summary of Contents for Virtex-5 RocketIO GTP





























































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 RocketIO GTP

Brand: Radionics Pages: 73

Brand: Daikin Pages: 4

Brand: IRiver Pages: 2

Brand: S&T Pages: 13

Brand: Radio Corporation Pty Pages: 75

Brand: IDT Pages: 25

Brand: HobbyKing Pages: 2

Brand: CMOSTEK Pages: 32

Brand: Napoleon Pages: 8

MultiView AK1200

Brand: Magenta Pages: 28

40103/202/3/5/10

Brand: RCD Pages: 2

Brand: Cinelex Pages: 6

Brand: National Pages: 25

Brand: Radio Shack Pages: 24

Brand: YEONHWA M TECH Pages: 19

Cloud Tv Box STB266

Brand: Sungale Pages: 16

Brand: IMG STAGE LINE Pages: 22

Brand: JBL Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands