Versant 80 Press
Customer Expectation & Installation Guide
21
Supported Media Types
Plain, uncoated, coated, transparencies, heavyweight, predrilled, hole punched, labels, letterhead
1 Tray Oversized High Capacity Feeder (OHCF)
Capacity
2,000 sheets (using Centerline Paper)
Sizes
Min: 7.2 x 8.3 in (182 x 210 mm), w/postcard kit 4 x 6 in (100 x 148 mm)
Max: 13 x 19.2 in (330 x 488 mm)
Weights
52 to 300 gsm
Supported Media Types
Plain, uncoated, coated, transparencies, heavyweight, predrilled, tabs, hole punched, labels, letterhead, postcard
(with Tray inserter)
Advanced High Capacity Feeder (Advanced HCF) - Single or Dual Configurationsconfigurations
Capacity
2,000 sheets (per tray); combined capacity of 4,000 sheets (using Centerline Paper)
Sizes
Min: 7.2 x 7.2 in (182 x 182 mm), w/postcard kit 4 x 6 in (100 x 148 mm)
Max: 13 x 19.2 in (330 x 488 mm)
Weights
52 to 350 gsm
Note: Optimal performance for coated stocks is 64 – 350 gsm
Supported Media Types
Plain, uncoated, coated, transparencies, heavyweight, predrilled, tabs, hole punched, labels, letterhead, postcard
(with Tray inserter)
Finishing Specifications
Offset Catch Tray (OCT)
The Catch Tray holds a maximum of 500 sheets.
Catch Tray Limitations:
If utilizing the Catch Tray, overall productivity will decline if offsetting mode is selected. The print engine will pause printing to offset between
sets, and then resume. Productivity loss depends on the number of sheets per set, with single-page jobs representing the worst case
(approximately 50% productivity loss)
Sheets smaller than 6.7 inches (170 mm) in the cross-process direction (e.g. the feed edge) cannot be offset
Sheets larger than 11.7 inches (297 mm) in the cross-process direction (e.g. the feed edge) cannot be offset
With the EX-i/EX Fiery Print Server, the Offset Jobs box on the Finishing tab must be checked to enable offsetting.
Interface Module
TIP: The Interface Module is required with any system configuration that has one or more finishing devices, except the Offset Catch Tray (OCT), BR
Finisher and BR Booklet Finisher. The Interface Module acts as a paper path from the press to the finishing device; it also allows communication
between the press and the finishing device. The Interface Module also cools and decurls paper as it exits the press and before it enters the finishing
device.
GBC Advanced Punch Pro
The GBC AdvancedPunch Pro is an inline die punch that uses modular die sets to create a variety of hole punch patterns in a range of papers
sizes, from A4 or 8.5 x 11 inch (LTR), long-edge-fed to 12x18 or SRA3 media, to support offline binding. The GBC AdvancedPunch Pro is
supported by all print servers. The GBC AdvancedPunch Pro requires an Interface Module as well as a High Capacity Stacker, Standard Finisher,
Booklet Maker Finisher, or Standard Finisher Plus (and additional third-party device).
GBC AdvancedPunch Pro
GBC
AdvancedPunch
Pro Specifications
Supports media from 75-300 gsm, (120-300gsm coated)
Supports tab stocks: letter (3, 4, 5, 8, 10 bank), ½ letter (3 and 5 bank), A4 (5 and 10 bank), and A5 (3 and 5 bank)
The GBC AdvancedPunch Pro is able to bypass all coated and uncoated media sizes and weights that are printed on the Press
Requires an additional electrical receptacle; refer to the
Electrical Requirements for Optional Devices
