background image

How Many and Of What Kind 
 

Your 

i-touch™ / Autocloser™

 kit has limits on the number of fingerprints and 

codes which can be entered. Those limits are as follows: 
 
1.  Only one Master User can exist. That master can choose to use a Master 

Fingerprint or to use a Master Code, but not both.  

 

a)  Fingerprint option can be used to verify master authenticity and also to 

 

     gain access to the secure area (open the door).  

 

b)  Code option can only be used to verify master authenticity when  

 

 

setting up the 

i-touch™ / Autocloser™

  kit. It cannot be used to 

 

 

access the secure area. Using a Master Code shared between trusted 

 

 

people could allow those several people the rights for things such as 

 

 

adding new users. 

2.  Regardless of whether a Master Fingerprint or Master Code was chosen, up 

to 29 additional fingerprints and up to 29 additional codes can be stored.  

      While the fingerprints are mated to a specific user’s finger, the codes can  
      be linked to either a specific user or to a group of users. For instance: 
 

i)   Permanent fingerprint of a user is established so the user always  

 

can enter a secured area and doesn’t need a physical door key. 

 

ii)  Temporary fingerprint of user with 6 days of activity could be issued to  

 

 

allow the user to feed your pets while you are on vacation. 

 

iii)  Permanent code ‘

192837

‘ could be given to a single child, or to all the  

 

 

members of your family. 

 

iv) Temporary code ‘

5474

‘ with 21 days of activity could be given to a 

 

 

small team of contractor workers, and once that time is up those  

 

 

workers no longer have access to the secure area. 

 

Instructions

 

Summary of Contents for i-touch
























Reviews: