manualshive.com logo in svg

XAG P30, Maintenance Manual, Page: 15 / 56

Share
Download
XAG P30 Maintenance Manual Download Page 15

15

1.

Reassemble the Motor, Motor Mount, and Motor Mount Arm Clamp in order and tighten

the screws to re-secure each component. Insert the Motor connector through the

Airframe Arm and reconnect the connector.

2.

Inspect and ensure the antenna cord and feeder protective cover are assembled

correctly, then reconnect the connectors on the Central Compartment Cover and

tighten the screws to re-secure the cover.

3.

Reassemble the Motor Housing Protective Pad, Nozzle and Propeller in order and

tighten the screws to re-secure each component.

I.

Ensure there are no loose or missing screws.

II.

Avoid foreign matter scratching the motor wiring.

III.

Avoid liquid or stain when connecting or disconnecting the connectors.

IV.

After reassembling, inspect and ensure the motor is installed correctly and level.

•

After the reassembly of the motor is completed, perform motor idletest and observe if the
XAG Agri APP reports any error.

🔎 

CHECK :

 

IMPORTANT:

🛠

Assemble:

@2020 XAG Australia All Rights Reserved 

Summary of Contents for P30

























































Reviews:

No comments