manualshive.com logo in svg

XAG P30, Maintenance Manual, Page: 10 / 56

Share
Download
XAG P30 Maintenance Manual Download Page 10

10

Landing Skids 

•

Use a 3.0 screwdriver to remove the fastening screws between the Landing skids and the
Airframe, and take out the hookdown point , nut bars , battery rails , and the landing skids
that need to be replaced. 

 

The screws using M4*16*8  Hexagon socket combination screw here. 

•

Note: By removing the corresponding screws , the landing skid can be disassembled into
three parts: the front landing skid , the centre landing skid , and the rear landing skid . Only
the damaged part can be replaced.

🔧

Disassemble:

P30 2019 Landing Skid (Rear Left)

*1

SKU-14-002-00070

P30 2019 Hook Down Point

*1

SKU-02-002-03439

P30 2019 Landing Skids Nut Bar 

*1

SKU-02-002-04244

P20/P30 2019 Battery Rail

*1

SKU-14-002-00119

M4*16*8  Hexagon socket combination screw

*8

SKU-02-004-00228

 💡

 

What do we need in this section:

 

The Landing Skids are total of five SKU codes according to different parts.

@2020 XAG Australia All Rights Reserved 

Summary of Contents for P30

























































Reviews:

No comments