X-Trax VP-1003 User Manual Download Page 59

Page: 59 / 60

- 59 -



Call control features: Flexible dial map, hotline, empty calling No. reject service, black list

for reject authenticated call, limit call, no disturb, caller ID, Flexible deer peer rule.



Support phonebook 500 records

，

Incoming calls / outgoing calls / missing calls. Each

supports 100 records



Support conference on server.



Support IAX2



Phonebook supports vcard standard



12/24 hours time display



Support daylight saving time



Support path, gruu



Support SIP Privacy



Support SMS



Support Memo



Support WMI



Support Speed dial



Support Alarm clock

6.1.3. Network features



WAN/LAN: support bridge and router model



Support PPPoE for xDSL



Support basic NAT and NAPT



Support VLAN (optional: voice vlan/ data vlan)



NAT Penetrate, Stun Penetrate



Support DMZ



Support VPN (L2TP) function



Wan Port supports main DNS and secondary DNS server, can select dynamically to get DNS

in DHCP mode or statically set DNS address.



Support DHCP client on WAN



Support DHCP server on LAN



QoS with DiffServ



Network tools in telnet server: including ping, trace route, telnet client

6.1.4. Maintenance and management



Upgrade firmware through POST mode



Web ,telnet and keypad management



Management with different account right



LCD and WEB configuration can be modified into requested language, and support

multi-language dynamically shifted



Upgrade firmware through HTTP, FTP or TFTP Telnet remote management/

upload/download setting file



Support Syslog



Support Auto Provisioning (upgrade firmware or configuration file)



Summary of Contents for VP-1003





























































Search results

Summary of Contents for VP-1003

Reviews:

Related manuals for VP-1003

Brands by name

Popular brands

X-Trax VP-1003, User Manual

Search results

Summary of Contents for VP-1003

Reviews:

Related manuals for VP-1003

Brands by name

Popular brands