X-pole X-Stage Instruction Manual Download Page 17 | Manualshive

Page: 17 / 20

X-pole X-Stage Instruction Manual Download Page 17

17

®

LEADERS IN POLE & AERIAL FITNESS

Copyright© Vertical Leisure Ltd. 2020 Version 3.0

All rights reserved.

Sandbag

Sandbag

Sandbag

Fig. (15.3)

Fig. (15.4)

It is important to place the Weight Plates on alternating plates as displayed in (Fig.15.4). Once all the Weight Plates are
installed place your sandbags or weights onto them and replace all the Floor Plates (as per pg. 9-10) and now your stage
is ready to be used (Fig.15.5).

5mm Hex Key

X

Static & Spin Screw

Bearing Carrier

Bearing Cone

‘A’ Pole

Static

Spin

Static & Spin Screw

Static & Spin Screw

‘X’ Mark

Static / Spin mode function

To change from Static to Spin mode, using the 5mm hex key, tighten the two hex screws contained within the 'X' marked
holes. To revert back to Spin mode, loosen the screws within the 'X' marked area. Do not forget, when removing your
pole, you must ensure that the pole is placed in Static mode (screws tightened/locked) prior to removal.

Fig. (16.1)

Fig. (16.2)

«
...
15
16
17
18
19
...
»

Summary of Contents for X-Stage





















Reviews:

No comments