Woxcon IPH400D User Manual Download

Page: 7 / 44

1080p IP Streaming Encoder/Decoder

3.2 IPH400D Decoder

①

POWER LED:

The LED illuminates green when power is applied.

②

Out LED:

The LED illuminates blue when the HDMI Out port is connected to

display device.

③

Link LED:

The LED illuminates blue when there is a valid LAN link between the

decoder and the network switch.

④

Storage:

Type-A USB to connect U-disk for video recording.

⑤

Recording LED:

The LED illuminates blue when recording video.

⑥

Start/Stop Button:

Press the button to start or stop video recording.

⑦

HDMI Out:

Type-A female HDMI port to connect HDMI display device.

⑧

Audio Out:

RCA jack to connect audio output device.

⑨

RS232:

3-pin terminal block for RS232 routing control. Supports point to point

unicast and point to multipoint broadcast configuration.

⑩

IR IN:

3.5mm jack to connect an IR receiver for IR routing control.

⑪

IR OUT:

3.5mm jack to connect an IR emitter for IR routing control.

⑫

LAN (PoE):

RJ45 port to connect directly to the encoder or a network switch using

a CATx cable.

⑬

DC 12V:

DC port for AC power adapter connection.

Summary of Contents for IPH400D












































Search results

Summary of Contents for IPH400D

Reviews:

Related manuals for IPH400D

Brands by name

Popular brands

Woxcon IPH400D, User Manual

Search results

Summary of Contents for IPH400D

Reviews:

Related manuals for IPH400D

Brands by name

Popular brands