Woxcon IPH400D User Manual Download Page 6

Page: 6 / 44

1080p IP Streaming Encoder/Decoder

3. Panel Description

3.1 IPH400E Encoder

①

POWER LED:

The LED illuminates green when power is applied.

②

In LED:

The LED illuminates blue when the encoder detects HDMI source input.

③

Out LED:

The LED illuminates blue when the HDMI Out port is connected to

display device.

④

Link LED:

The LED illuminates blue when there is a valid LAN link between the

encoder and the network switch.

⑤

HDMI In:

Type-A female HDMI port to connect HDMI video source device.

⑥

HDMI Out:

Type-A female HDMI port to connect HDMI display device.

⑦

RS232:

3-pin terminal block for RS232 routing control. Supports point to point

unicast and point to multipoint broadcast configuration.

⑧

IR IN:

3.5mm jack to connect an IR receiver for IR routing control.

⑨

IR OUT:

3.5mm jack to connect an IR emitter for IR routing control.

⑩

LAN (PoE):

RJ45 port to connect directly to the decoder or a network switch using

a CATx cable.

⑪

DC 12V:

DC port for AC power adapter connection.

Summary of Contents for IPH400D












































Search results

Summary of Contents for IPH400D

Reviews:

Related manuals for IPH400D

Brands by name

Popular brands

Woxcon IPH400D, User Manual

Search results

Summary of Contents for IPH400D

Reviews:

Related manuals for IPH400D

Brands by name

Popular brands