Worldcast Systems ECRESO FM 10kW, User Manual

Page: 106 / 243

ECRESO FM 5kW / 10kW, user manual – 11/2021
Page 106
WorldCast Systems SAS - 20 avenue Neil Armstrong - 33700 Mérignac (Bordeaux Métropole) FRANCE
+33 (0)5 57 928 928
– www.worldcastsystems.com – contact@worldcastsystems.com
NAME
Access
(R/W)
Possible value on the
serial port of the unit
Comments Module
MEAS.HEAT4 R ±[0..125]
Measures the
heatsink 4
temperature
ECU
MEAS.INT_TEMP R 0…999
Measure of the temperature of the internal
sensor.
ECU | DRVn
MEAS.LOAD1.TEMP1 R
- 999…999 XXXX
X=[0..9]
Reads the probe1 temperature in load 1 =>
999 when there is no communication, or
probe failed
ECU
MEAS.LOAD1.TEMP2 R
- 999…999 XXXX
X=[0..9]
Reads the probe2 temperature in load 1 =>
999 when there is no communication, or
probe failed
ECU
MEAS.LOAD1.TEMP3 R
- 999…999 XXXX
X=[0..9]
Reads the probe3 temperature in load 1 =>
999 when there is no communication, or
probe failed
ECU
MEAS.LOAD1.TEMP4 R
- 999…999 XXXX
X=[0..9]
Reads the probe4 temperature in load 1 =>
999 when there is no communication, or
probe failed
ECU
MEAS.LOAD2.TEMP1 R
- 999…999 XXXX
X=[0..9]
Reads the probe1 temperature in load 2 =>
999 when there is no communication, or
probe failed
ECU
MEAS.LOAD2.TEMP2 R
- 999…999 XXXX
X=[0..9]
Reads the probe2 temperature in load 2 =>
999 when there is no communication, or
probe failed
ECU
MEAS.LOAD2.TEMP3 R
- 999…999 XXXX
X=[0..9]
Reads the probe3 temperature in load 2 =>
999 when there is no communication, or
probe failed
ECU
MEAS.LOAD2.TEMP4 R
- 999…999 XXXX
X=[0..9]
Reads the probe4 temperature in load 2 =>
999 when there is no communication, or
probe failed
ECU
MEAS.M.PKMAX R - 150.0…150.0 Absolute value max of the channel M in kHz ECU | DRVn
MEAS.MPXPWR.10S R -320.00...+320.00 Value of the MPX power over 10 seconds ECU | DRVn
MEAS.MPXPWR.1M R -320.00...+320.00 Value of the MPX power over 1 minute ECU | DRVn
MEAS.MPXPWR.ATT R -320.00...+320.00
Value of the attenuation applied to limit the
MPX power
ECU | DRVn
MEAS.N12V R -xx.x x=[0..9] Measures the -12 V voltage ECU | DRVn
MEAS.OVDRTRIP R xx=[0..9] Counts amplifier overdrive faults PAn
MEAS.PCONS R [0..9999] Power used by unit ECU
MEAS.PFWD R [0..9999]
Measure of direct power. examples: "20" or
"300" => 300 W
DRVn | PAn | PSUn
MEAS.PFWD.AVG R [0..9999] Average measured power ECU
MEAS.PIN R [0..99.9] Measures the input power DRVn | PAn | PSUn
MEAS.PREF R xxx.x x=[0..9] Measure of reflected power: "20" => 2 W DRVn | PAn
MEAS.PREFTRIP R xx=[0..9] Counts amplifier reflected power faults PAn
MEAS.PRESSURE R 0…2000
Measure of the pressure on the internal
sensor.
ECU | DRVn
MEAS.PSU_TEMP R ±[0..125] Measures the temperature of the PSU DRVn
MEAS.S.PKMAX R - 150.0…150.0 Absolute value max of the channel S in kHz ECU | DRVn
MEAS.SFM R [0..125]
SmartFM coefficient to be applied to the set
power
ECU
MEAS.SFN.DELAY R 0… 5000000.00 Delay applied to the signal in µs ECU | DRVn
MEAS.SUPPLYTRIP R xx=[0..9] Counts amplifier current faults PAn
MEAS.TEMPTRIP R xx=[0..9] Counts amplifier temperature faults PAn
MEAS.VOLT1 R xxx.x x=[0..9]
Measures the power supply 1 voltage.
Example: "48.0" =>48.0 V
DRVn | PAn | PSUn
MEAS.VOLT2 R xxx.x x=[0..9]
Measures the power supply 2 voltage.
Example: "48.0" =>48.0 V
PAn | PSUn