manualshive.com logo in svg

Worcester GR2300iW C, Installation And Maintenance Instructions Manual

Share
Download
Worcester GR2300iW C Installation And Maintenance Instructions Manual Download Page 60

Inspection and maintenance

 

Greenstar 2000 – 6 721 820 552 (2021/02)

60

9.3

Component access

Removing the front casing

The front casing is secured with two screws which are critical to maintain 
the case seal and to prevent unauthorised removal (electrical safety).

▶ Always secure the casing with these screws.

▶ Loosen the two screws [1] and pull the bottom of the casing forward.
▶ Lift off the casing.

Fig. 71 Removing the front casing

9.4

Fan pressure test

NOTICE

Fan pressure test

▶ The appliance must be running at maximum output in chimney sweep 

mode for the fan pressure test, (

 Setting the appliance to 

maximum).

This test is to determine if the heat exchanger requires cleaning or 
additional actions.

Fan pressure test reading.

▶ The pressure reading will be in negative values.

9.4.1

Checking heat exchanger assembly

▶ Remove the front casing.
▶ Remove the cap from the test nipple, and connect a pressure gauge.

Fig. 72  Test nipple at the mixing device

Appliance fan pressure test values

Natural Gas and LPG appliances

Table 32 Natural Gas and LPG values

If the manometer reading is within tolerance

, in the white area of the 

table values.
▶ The heat exchanger/exhaust path/siphon does not require attention.

If the manometer reading is out of tolerance

, in the shaded area of the 

table values then carry out the following checks.
▶ Check that the siphon is not restricted or blocked.
▶ Check the exhaust paths for restrictions.
▶ Clean the heat exchanger with a suitable cleaning tool, refer to 

cleaning section.

▶ Re-check the fan pressure readings.

If the appliance, after completing the above checks, fails the fan 
pressure test then contact Worcester, Bosch Group for advice.

▶ Switch the appliance off after completing pressure check. 
▶ Disconnect the digital manometer and replace the test point cover.

9.5

Check working gas inlet pressure

NOTICE

Gas inlet pressure

▶ Do not continue with the other checks if the correct gas inlet pressure 

can not be achieved at maximum output.

▶ Check the gas supply working pressures in the system conform to the 

readings shown in the table shown in chapter 6.6 "Checking gas inlet 
pressure".

1

0010029675-001

Appliance 

output

Cleaning required

No cleaning required

Value

30kW

0 mbar

-4.7 mbar -4.8 mbar

-12 mbar

25kW

0 mbar

-3.2 mbar -3.3 mbar

-12 mbar

0010036064-001

Summary of Contents for GR2300iW C





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands