manualshive.com logo in svg

Worcester GR2300iW C, Installation And Maintenance Instructions Manual

Share
Download
Worcester GR2300iW C Installation And Maintenance Instructions Manual Download Page 20

Pre-Installation

 

Greenstar 2000 – 6 721 820 552 (2021/02)

20

Flue system bends

NOTICE

Effective flue lengths of bends:

Each bend used has an equivalent straight flue length.

▶ Refer to table 16.

Table 16 Effective length of bends

4.4.2

Flue options

The systems have different maximum flue lengths, refer to the following 
example flue options for those maximum flue lengths.

Horizontal high level flue assembly

Fig. 14 Horizontal flue option

• Flue length [L] (initial bend included in length calculation)

– 60/100 = 202 - 603mm
– 80/125 = N/A

Telescopic horizontal flue assembly

Fig. 15 Horizontal flue option

Telescopic horizontal flue assembly [A]
• Flue length [L] (adaptor bend included in length calculation)

– 60/100 = 180 - 570mm
– 80/125 = 405 - 600mm

Extended telescopic horizontal flue assembly [B]
• Flue length [L] (adaptor bend included in length calculation)

– 60/100 = 570 - 790mm
– 80/125 = N/A

Horizontal fixed length flue assembly

Fig. 16 Horizontal flue option

• Flue length [L] (adaptor bend included in length calculation)

– 60/100 = 330 - 1,050mm
– 80/125 = N/A

Extended horizontal flue

Fig. 17 Horizontal flue option

• Flue length [L] (adaptor bend included in length calculation)

– Maximum flue length as stated in   "Horizontal maximum flue 

lengths".

Horizontal flue with additional 90° elbow

Fig. 18 Horizontal flue option

• Flue length [L] (adaptor bend included in length calculation)

– Maximum flue length as stated in   "Horizontal maximum flue 

lengths" minus the 90° bend equivalent straight flue length as 
stated in  Table 16  "Effective length of bends".

Horizontal flue with additional 90° elbows

Fig. 19 Horizontal flue option

• Flue length [L] (adaptor bend included in length calculation)

– Maximum flue length as stated in   "Horizontal maximum flue 

lengths" minus 2 x 90° bends equivalent straight flue length as 
stated in  Table 16  "Effective length of bends".

Effective flue length

Bend

60/100

80/125

45°

0.5m

0.5m

90°

1.5m

1.5m

0010015190-001

383 mm - 603 mm

60/100 mm

130 mm Min

0010015191-001

[A] 350 mm - 570 mm
[B] 570 mm - 790 mm

60/100 mm

130 mm Min

0010015192-001

330 mm Min

1050 mm

0010015193-001

0010015194-001

0010015195-001

Summary of Contents for GR2300iW C





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands