manualshive.com logo in svg

Worcester GR2300iW C, Installation And Maintenance Instructions Manual

Share
Download
Worcester GR2300iW C Installation And Maintenance Instructions Manual Download Page 48

Commissioning

 

Greenstar 2000 – 6 721 820 552 (2021/02)

48

6.5

Chimney sweep mode

You have 30 minutes to take your measurements or to check or adjust the 
appliance settings. After this time the appliance returns to normal 
operation.

Whilst the appliance is in chimney sweep mode, the chimney sweep 
symbol ( 

C

 ) will be displayed on the screen.

6.5.1

Setting the appliance to maximum

Maximum output mode

▶ A hot water outlet can be opened to prevent the appliance from 

shutting down due to high temperature during testing.

▶ Press the 

ok

 button for at least 5 seconds.

– The appliance enters chimney sweep mode and automatically 

enters maximum output. 

– The display shows the maximum percentage of the power 

100%

 

alternating with the flow temperature.

– The appliance will ramp up to maximum output in approximately 

30 to 35 seconds.

6.5.2

Setting the appliance to minimum

Whilst the appliance is already in chimney sweep mode - maximum 
output.
▶ Press the 

 button to set the appliance to minimum output.

– The display shows the minimum percentage of the power 

alternating with the flow temperature.

– The appliance will take approximately 30 to 35 seconds to ramp 

down to minimum output.

– Allow the appliance to stabilise at minimum output.

6.5.3

Exiting chimney sweep mode

To exit the chimney sweep mode:

▶ Press the 

ok

 button and the appliance will return to normal operation.

– If left in the chimney sweep mode the control will return to normal 

operation after 30 minutes.

6.6

Checking gas inlet pressure

Measuring the inlet pressure

▶ Switch off the appliance and close the gas isolator.
▶ Unscrew the screw on the test nipple for the gas supply pressure and 

connect a pressure gauge.

Fig. 63 Checking the gas supply pressure (above: SIT valve, below: 

Honeywell valves)

[1]

Gas valve - NG

[2]

Gas valve - LPG

▶ Open the gas isolator and switch on the appliance.
▶ Ensure that there is heat transfer by opening the radiator valves and 

any zone valves fitted. A hot water tap can also be opened for 
additional heat transfer.

▶ Set the appliance running at maximum output in chimney sweep 

mode (

  6.5 "Chimney sweep mode").

▶ Check the required gas supply pressure according to following 

section   "Gas pressure within the system".

Commissioning must not take place outside of the permissible pressure 
range. 

▶ Identify the cause and rectify the fault.
▶ If this is not possible: isolate the device on the gas side and notify the 

gas supplier.

▶ Exit the chimney sweep mode.
▶ Switch off the device, close the gas isolator, remove the pressure 

gauge and tighten the screw.

▶ Refit the casing.

T10

0010035320-001

1

2

Summary of Contents for GR2300iW C





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands