13
G
Assembly
Storage box/charging station
z
Assemble the storage box in a dry location that remains frost-
free in the winter.
z
The storage box can be used as a charging station. If you want
to use it for this purpose, place the storage box no further than
150 cm away from a mains socket
.
1. Use the base plate as a drilling template
to mark the upper
fastening points (1) (2).
2. Install two screws at the fastening points (Ø 8mm screw head)
with the shaft of the screw heads protruding approx. 6-8 mm
from the support.
3. Hook the storage box on the screw heads.
4. Use a third screw to attach the storage box at the bottom bore
(3).
Operation
Times of operation
z
Please consult regional/local regulations.
z
Inquire about the operating times at your local regulatory agen-
cy.
Charging the battery
General charging instructions
1
Caution! The charger must only be operated in dry
rooms.
Recharge only with the original WOLF-Garten charger (part no.
7266 077)!
Charge the battery before using the mower for the first time.
For charging times, see page 10.
Charging inside the storage box
1. Fix the charging plug inside the locking mechanism of the
storage box (1).
2. Connect the charger to the mains socket (230 V~)
(2).
3. Place the battery-powered shears inside the storage box (3).
Charging outside of the storage box
1. Connect the charger to the mains socket (230 V~)
(1).
2. Insert the charging plug into the charging socket of the battery-
powered shears (2).
3
Instructions for the handling of the charger
:
z
The red LED indicates charge process. When the LED
goes out, the lithium-ion battery is charged.
3
General instructions regarding the battery:
To prolong the service life of the battery, observe the
following instructions:
z
Low battery voltage will reduce the stroke rate of the
shears. In such a case, recharge the battery.
z
Always recharge the lithium-ion battery prior to any
prolonged period of non-use, i.e. before storing the
shears away in winter.
z
For charging times, see page 10.
z
The lithium-ion rechargeable battery can be charged at
any charge level and charging can be interrupted at any
time without damaging the battery (no memory effect).
z
Self-discharge of the battery! Disconnect the plug from
the charger of the battery-powered shears as soon as the
charger is disconnected from the mains.
Switching the battery-powered shears on/off
1. Slide the safety button (1) forward and hold it.
2. Press the control button (2).
3. Release the safety button (1).
4. To switch the battery-powered shears off, release the safety
button (2).
Tips for shape trimming ornamental shrubbery
z
Create a template using cardboard
or a different light, large-
surface material
which makes it easy to achieve an even trim,
e.g. for a sphere.
z
Another way to create a template is to use slats and string
and form, for instance
,
a
cone.
z
Contour shears are particularly well suited for delicate fine cuts
of shaped shrubs
.
Maintenance
Storage
z
Make sure to store the battery-powered shears out of the reach
of children.
z
Always attach the blade guard for transport and storage.
z
Always recharge the lithium-ion battery prior to any prolonged
period of non-use, i.e. before storing the shears away in winter.
z
Store the battery-powered shears in a dry and frost-free location.
z
When storing the tool in the storage box for an extended period
(e.g. in the winter), disconnect it from
the power supply (2) as
well as the plug adapter (1) and store the power supply unit and
any other accessories in their designated locations.
z
Attach the cover to protect the battery-powered shears including
accessories.
General instructions
1
Caution! Counterrotating blade
Before carrying out any maintenance or cleaning work:
z
Never actuate the switches
(1) (2).
z
Do not touch the moving blade.
Cleaning
z
Clean the battery-powered shears after every use with a dry
cloth. If necessary, use a brush to remove persistent dirt.
z
Clean and lubricate the gearbox at the end of the gardening
season (see "Cleaning or replacing the blade").
z
Never clean the battery-powered shears with a water jet.
Cleaning or replacing the blade
3
Blunt blades should not be resharpened but replaced.
1. Lift the locking mechanism
(1) and pull the sliding shoe away
to the back (2).
2. Remove the blade from the battery-powered shears.
3. Grease the plastic ring of the blade
using petroleum jelly.
4. Clean the visible part of the gearbox and lubricate it with grease
if necessary.
5. Fix
the blades in place on the gearbox cover
.
6. Slide the sliding shoe over the battery-powered shears until the
locking mechanism engages
(blade will automatically snap
into the gearbox).
A B
B
A
B C
B
C
B C
D
J K L M N
K
L
J
M
N
B
B
D
D
E F G H
E
F
G
H
0054641.book Seite 13 Mittwoch, 8. April 2009 3:15 15
