WITTUR WGG-29.1 Operating Instructions Manual Download Page 59

Page: 59 / 59

Installation and Operational Instructions for ROBA

-diskstop

Type 894.5_ _._ _ Size 10

(B.8.4.5.EN)

23/03/2017 TK/TL/GC/SU

Chr. Mayr GmbH + Co. KG

Eichenstraße 1, D-87665 Mauerstetten, Germany

Tel.: +49 8341 804-0, Fax: +49 8341 804-421

Page 16 of 16

www.mayr.com

, E-Mail:

[email protected]

Malfunctions / Breakdowns:

Malfunction

Possible Causes

Solutions

Brake does not release



Incorrect voltage on rectifier



Rectifier failure



Air gap too large (worn friction lining)



Coil interrupted



Incorrect rectifier (e.g. normal rectifier
without overexcitation)



Apply correct voltage



Replace rectifier



Replace the friction pads



Replace brake



Use the correct, appropriate rectifier

mayr

will take no responsibility or guarantee for replacement parts and accessories which have not been delivered by

mayr

, or for damage resulting from the use of these products.

Summary of Contents for WGG-29.1




























































Search results

Summary of Contents for WGG-29.1

Reviews:

Related manuals for WGG-29.1

Brands by name

Popular brands

WITTUR WGG-29.1, Operating Instructions Manual

Search results

Summary of Contents for WGG-29.1

Reviews:

Related manuals for WGG-29.1

Brands by name

Popular brands