Assembly and Operating Instructions
– Industrial sectional door MakroPro 100
,
MakroPro Alu 100
8
EN
IIiO/BS/MakroPro100/10/2015/ID-92974
+
Technical description
• Avoid strong striking the door leaf against frame, so called „door banging”,
that may result in cracking of paint coating and glazing, in door leaf deforma-
tion, and negatively influence operation of hardware, hinges, gaskets.
• It is prohibited to overload the wicket door leaf, leave the objects within the
door leaf movement area as well as operate the door by force.
[C000089] It is recommended to equip the wicket door with self-closer, which
should only be used for self-closing of the wicket door after its previous manual
opening.
[C000209]
It is prohibited to put any objects between the
opening or closing door leaf and frame.
Caution! Risk of accident.
[C000090] Each time before operating the door, it is necessary to make sure
that the wicket door is closed. Wicket door installed in the door with electric
drive must be equipped with limit switch, which prevents the drive switching-on
if the wicket door is open.
[C000091] It is prohibited to apply extra force (other than the self-closer) to fully
close or speed up the wicket door closing, that may result in damage or poor
adjustment of self-closer.
[C000015]
14. ROUTINE MAINTENANCE INSTRUCTION
Activities, which may be performed by the Owner after careful
reading of the Instruction supplied with the door:
[C000051] To clean door sections, a sponge and clean water, or neutral lac-
quer-cleaning agents available in stores should be used.
At least once for three month, and once in a month for industrial doors, carry out
the door periodic inspections, including:
• check cable tension and condition (damaged wires, corrosion),
• check all connections and joints, including screws to mount the guides and
hinges,
• if any irregularities are observed, make sure to eliminate them,
• check the assembly of the drive,
• check the connection of a key with shaft.
[B000029] Dry, clean and very soft, preferably cotton fabrics, must be used to
clean the panes in glazing (windows, glazed aluminium profiles). Non-scrub-
bing cleaning agents, e.g. wash-up liquid with neutral pH value may be used,
but it is recommended to perform a trial on a small surface previously. The pane
must be rinsed with water thoroughly before cleaning (it is not recommended to
use high-pressure cleaning appliances) in order to remove particles of impurities
and dust that may cause scratching of pane surface. It is not recommended
to use cleaning agents that contain alcohol or solvents (they cause permanent
tarnishing of pane surface).
• [C000057] lubricate rollers, bumpers and hinges with e.g. semi-solid HWS-
100 Wurth grease at least once in six months.
• [C000056] At least once for 12 month, exchange the batteries in remote
controls.
• In doors with an electrical drive, check the proper adjustment of limit switches.
For this purpose, press the corresponding button (up or down) on a control
panel, and observe where the door stops. When the door is in its ultimate
closed position, the cables should remain tightened. When the door is in its
ultimate open position, the bottom sealing should not be above the opening
clear height.
• In doors with an electrical drive, check the operation of electrical safety de-
vices (if applicable) once in a month:
• photocells - simulate the work conditions situation. For this purpose
cross the light beam - the door should stop and return to its previous
position,
• optical safety edge - the door should stop and reverse, when the leaf
touches 80 [mm] in diameter and 50 [mm] high object located on the
floor. If necessary, adjust and check again. Improper adjustment may
cause an accident.
• lock sensor - when the lock is closed, the door should not start its opera-
tion,
• wicket door sensor - when the wicket door is open, the door should not
start its operation.
• Check the operation of emergency opening supplied with the actuator.
[C000058]
Activities, which may be performed by qualified per-
sonnel with corresponding permits:
• at least once in six months, and once in three months for industrial doors,
carry out the door periodic inspections, including:
• check the condition of cables along its whole length for any defects (dam-
aged wires, corrosion). Check if the cables are properly mounted on drums,
• check if all joinings and joining parts are bolted properly. Special attention
should be paid to bolts to mount guide rails and screws to mount hinges as
well as keys and actuator mounting,
• check the cable break safety devices,
• if there are any faults in electrical drive operation, switch off drive power
supply for 2÷3 min, then switch it on again,
• check the rollers and adjust them if necessary,
• check the wicket door and adjust it if necessary,
• if any faults are observed, make sure to eliminate them,
• all activities should be performed according to the Assembly and Operating
Instruction.
[C000059]
Activities, which may be performed by an authorized
service centre of “WIŚNIOWSKI” Sp. z o.o. S.K.A.
• any door modifications,
• replacement of the cable break safety devices,
• replacement of cables and cable drums,
• repairing of electric components,
• repairing of door components.
• [A000060]
Disconnect the drive power supply during
all maintenance and inspection works.
• [C000233]
It is allowed to loosen the leaf supporting
cables only when the door is in its closed position.
[C000045]
15. RESTRAINTS IN DOOR OPERATION
The door is not intended to be used:
• in an explosive environment,
• as a fire-proof partition,
• in moist rooms,
• in rooms with chemical substances harmful to the protective and paint coatings,
• from the sunny side in case of dark-coloured door leaves,
• as a bearing structure of a building,
• as a hermetic barrier.
[A000011] All works must be performed according to this Assembly and Op-
erating Instruction of the door. Any comments or recommendations must be
submitted to the Owner in writing, e.g. to be noted in the door report book or
warranty card, and submitted to the door Owner. Upon performing the inspec-
tion, this fact must be confirmed by corresponding note in the door report book
or warranty card.
[A000012]
“WIŚNIOWSKI” Sp. z o.o. S.K.A. reserves the right to
introduce design modifications due to technological progress that
do not alter the product functionality, without prior notice.
This documentation is copyright of “WIŚNIOWSKI” Sp. z o.o.
S.K.A. Copying, reproduction and usage in full or in a part with-
out the written consent of the owner is prohibited.
[A000048]
This document has been translated from Polish. In case
of discrepancies, the Polish version prevails.
