Wisenet PNM-9031RV User Manual Download Page 21 | Manualshive

Page: 21 / 32

background image

English _

21

!

INST

ALLA

TION & CONNECTION

Connecting to Audio Input/Output

Network

PC

Microphone

Speaker

Microphone

Speaker

1.

Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the
microphone is connected to.

2.

Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the amplifier that the
speaker is connected to.

3.

Check the specifications for audio input.

~

Audio Codec

- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate:

16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling
Frequency: 16kHz)

~

Full duplex Audio

~

Audio in

: Selectable (microphone/Line-in), Supported voltage: 2.5VDC (4mA), Input impedance: 2K Ohm

~

Audio out

: Line-out (3.5mm mono jack), Maximum output: 1Vms, Line out impedance : 600Ω

Connecting to the I/O port box

Connect the Alarm I/O cable to the corresponding port of the port box.

Sensor

Alarm

(Warning lamp)

~

ALARM #1, ALARM #2 : These ports can be used as alarm input or output ports. If used as input ports,

alarm input or day/night sensors can be connect to them. If used as output ports,
alarm output signals can be connect to them.

※

Alarm I/O changes can be made through the Webviewer setup.

~

GND : Common port for alarm in/output signal.

«
...
19
20
21
22
23
...
»

Summary of Contents for PNM-9031RV

































Reviews:

No comments

Related manuals for PNM-9031RV

Brand: G-Tek Pages: 28

Brand: D-Link Pages: 24

DCS-3110 - SECURICAM Fixed Network Camera

Brand: D-Link Pages: 16

Brand: D-Link Pages: 12

Brand: D-Link Pages: 18

BugHunter Professional CR-01

Brand: i4Technology Pages: 9

Anycam IR-3MIPS08 Series

Brand: I-View Pages: 8

Brand: Sabre Pages: 50

Brand: Vacron Pages: 2

Brand: Z-Wave Pages: 6

Brand: Z3 Technology Pages: 5

X Wireless Series

Brand: Axess Pages: 8

Brand: Digimerge Pages: 44

Brand: LONGHORN Pages: 15

Brand: 3xLogic Pages: 16

iDS-2CD6124FWD-B

Brand: HIKVISION Pages: 29

Brand: Q-See Pages: 20

Brand: Olympus Pages: 202

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands