Wisenet PNM-9031RV User Manual Download Page 16 | Manualshive

Page: 16 / 32

background image

installation & connection

16_

installation & connection

6-3.

Mount the cable bushing to the camera body.

6-4.

Connect the network cable jack to the PoE+ port of the camera.

[Installing audio/alarm cables]

7.

Plug the cable bushing of the provided audio/alarm cable into the camera body.

8.

Connect the connector of the audio/alarm cable to its connection port.

«
...
14
15
16
17
18
...
»

Summary of Contents for PNM-9031RV

































Reviews:

No comments

Related manuals for PNM-9031RV

Concord express

Brand: GE Pages: 3

Concord express

Brand: GE Pages: 32

Brand: Falltech Pages: 52

Brand: Caddx-Caddi Controls Pages: 6

Brand: Magellan Pages: 68

Brand: Magellan Pages: 2

Brand: Magellan Pages: 52

Brand: Magellan Pages: 12

Brand: Magellan Pages: 48

Luxomat PD2-DIM Series

Brand: B.E.G. Pages: 2

LUXOMAT PD4-M-1C-C-PS

Brand: B.E.G. Pages: 4

Brand: ACS Pages: 64

Brand: Arecont Vision Pages: 3

Brand: Velleman Pages: 56

Brand: R&TTE Pages: 6

Vingtor Stentofon SPA-AC6

Brand: Zenitel Pages: 54

Brand: Ihagee Pages: 32

Brand: TUYA Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands