8
OPM-109
REV B
ENGINE
Refer to the engine operators manual for more detailed operation and
maintenance information.
CAUTION: EQUIPMENT DAMAGE:
%HVXUHWRFKHFNWKHHQJLQHRLOOHYHOIUHTXHQWO\DVVSHFL¿HGLQWKH
engine manual.
The engine manufacturer has established an excellent worldwide
HQJLQHVHUYLFHRUJDQL]DWLRQHQJLQHVHUYLFHLVDYDLODEOHIURPDQHDUE\
DXWKRUL]HGGHDOHURUGLVWULEXWRU*RWRWKH:,1&2ZHEVLWHIRUDOLVWRI
HQJLQHGHDOHUVKWWSZLQFRJHQFRP(QJLQHB6XSSRUWRUFRQWDFWWKH
WINCO Service Department.
The rated power of each engine-generator is limited by the
WHPSHUDWXUHDOWLWXGHDQGDOORWKHUDPELHQWFRQGLWLRQVVSHFL¿HGE\
the engine manufacturer. Engine power may decrease 3½% for each
1000 feet above sea level, and will decrease an additional 1% for each
10 degrees Fahrenheit above 60° Fahrenheit. Units should not be
operated in ambient temperature greater than 125° Fahrenheit.
GENERATOR
:,1&2JHQHUDWRUVHWVXVHEUXVKOHVV$95$XWR9ROWDJH5HJXODWRU
controlled broad-range generator ends. The generator converts
rotational mechanical energy into electrical energy. These WINCO units
are equipped with generators manufactured by Cummins Generator
Technology. Each generator ‘end’ has its own data tag. A unique serial
number is on the data plate.
MODEL NUMBER STRUCTURE
The WINPOWER alpha-numerical numbering consists of a base model
designation, followed by an options section, separated by a dash mark.
The base component of the model numbering system identifies an
engine type, engine starting method, fuel type, kilowatt rating, engine
manufacturer, and number of generator poles. Following the separation
dash mark is the voltage connection and optional installed equipment.
2SWLRQVLQFOXGHIHDWXUHVOLNHZHDWKHUHQFORVXUHVKRXVLQJEDVH
PRXQWHGIXHOWDQNVL]HVDQGWUDLOHURSWLRQV
Please note that some features or packages, such as NFPA level I
& II, do not have an indication place in this numbering system. They
DUHLVVXHGDQGEXLOWZLWKDQ06SHFLH0QXPEHUZKLFKFDQ
be found on the WINPOWER data tag. When the M-Spec is present,
supplemental inserts will accompany this standard manual providing
information about the special equipment and features installed. The
standard model numbering key that can be used along with the data
tag information and/or M-Spec supplements to determine the generator
set’s ratings and specifications.
D
D = Diesel
R
R = Remote Start
30
Generator Output Rating in kW
I
(QJLQH0DQXIDFWXUHU, ,VX]X) )37
4
Number of Generator Poles
-
Base Unit - Options Separator
A
Voltage
$ 6LQJOH3KDVH9
' 7KUHH3KDVH9
- 7KUHH3KDVH9
/ 7KUHH3KDVH9
A
HOUSING TYPE
A = Sound Attenuated/Weather Protective
* = No Housing
M
)XHO7DQN6L]H6 6PDOO0 0HGLXP/ /DUJH
3 3ODVWLF 1RQH
T
7 7UDLOHU 1RQH
D
Battery Charger Options
$ 9$% 9$& 9$' 9$
( 9$1)3$) 9$1)3$* 9$
+ 9$, 9$1)3$- 9$
. 9'&$'6(/ 9'&$'6(
PREPARING THE UNIT
UNPACKING
1. As you receive your unit, it is critical to check it for any damage. If
any damage is noted, it is always easiest to refuse the shipment and
let WINCO take care of the freight claim. If you sign for the unit, the
WUDQVIHURIWKHRZQHUVKLSUHTXLUHVWKDW\RX¿OHWKHIUHLJKWFODLP
2. Before proceeding with the preparations of your new generator
for operation, take a couple of minutes to ensure the unit you have
UHFHLYHGLVWKHFRUUHFWPRGHODQGUHYLHZWKHVSHFL¿FDWLRQSDJHVLQWKLV
manual to ensure that this unit meets your job requirements.
CAUTION: EQUIPMENT DAMAGE:
This unit is shipped with oil and a 50/50 mix of coolant. Be sure to
FKHFNDOOÀXLGOHYHOVEHIRUHRSHUDWLQJ6HHHQJLQHPDQXIDFWXUHU¶V
instruction manual for recommended oil requirements before initial
starting.
Once generator set is on-site:
1. Carefully remove the crate.
2. After inspecting the engine-generator for external, physical damage,
locate and check the following items packed with the unit:
a. Installation and Operator’s Manual.
b. Engine manufacturer’s instruction manual.
c. Battery hold-down brackets & hardware.
d. Unit components or accessory items shipped loose for on-site
installation.
e.
Optional
accessories.
3. Remove main frame hold-down bolts.
4. Unit can now be lifted from shipping rails.
