WhisperKool 4000 Condenser Owner'S Manual Download | Manualshive

Page: 23 / 58

background image

www.whisperkool.com | Page 21

INSTALLING THE UNIT FROM INSIDE THE CELLAR

NOTE:

The Ceiling Mount Unit can still be used even with limited or no above ceiling access. For installations with

limited or no above ceiling access, do not remove the top of the evaporator unit. Follow the instructions below for

installation.

1.

Remove the knockouts from the top of the unit for

the line set and electrical.

2.

Route all electrical and tubing to the installation

location as outlined on page 14.

4.

Route the line set, drain line, water line, power wires,

keypad cable, bottle probe cable and humidistat cable

into the evaporator housing through the knockouts

removed in the first step.

Note: Depending on installation location, the Flush Mount

mounting option might not be suitable.

5.

Mount the evaporator unit to the ceiling using the

supplied 1 ¾” hex head screws.

3.

Install the mounting bracket as shown on page 17.

LINE SET

DRAIN LINE

POWER CABLE

WIRING

KNOCKOUT

BOTTLE PROBE &

KEYPAD WIRING

KNOCKOUT

«
...
21
22
23
24
25
...
»

Summary of Contents for 4000 Condenser



























































Reviews:

No comments

Related manuals for 4000 Condenser

Brand: GE Pages: 72

Brand: Vax Pages: 7

Brand: Kampmann Pages: 96

Brand: Kampmann Pages: 36

Brand: S&S Cycle Pages: 8

Brand: RollSeal Pages: 44

Hazardous Location HL Series

Brand: Kooltronic Pages: 19

Brand: Daewoo Pages: 21

Brand: A.O. Smith Pages: 16

Super Multi NX FTXG25JV1BW

Brand: Daikin Pages: 242

Brand: Daitsu Pages: 120

Brand: Daewoo Pages: 19

Brand: Morgan Pages: 4

Brand: b-mola Pages: 8

ILLUSION MCD 048 D1

Brand: Trane Pages: 20

Brand: Daikin Pages: 501

Brand: Haier Pages: 537

Brand: Samsung Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands