WhisperKool 4000 Condenser Owner'S Manual Download

Page: 9 / 58

www.whisperkool.com | Page 7

Receiving and Inspecting the System

•

Lift only at the designated hand hold locations on the shipping container or fully support the unit from

underneath. A shipment may include one or more boxes containing accessories.

•

Inspect the packaging for any obvious signs of damage or mishandling before opening the container.

•

Note any discrepancies or visual damage on the Bill of Lading before signing.

•

Place the box containing the unit on a tabletop to prepare it for testing prior to installing.

•

Sit unit upright for 24 hours.

Note: WhisperKOOL units are manufactured in the USA and tested prior to shipment.

Review the Packing Slip to Verify Contents

•

Check the model number to ensure it is correct.

•

Check that all factory options ordered are listed.

If any items listed on the packing slip do not match your order information,

contact WhisperKOOL Customer Service immediately.

Check the Evaporator Unit (Fan Coil Unit) Box for the Following Contents:

RECEIVING & INSPECTING THE SYSTEM

Please leave the unit in its original box until you are ready for installation. This will allow you to move the product

safely without damaging it. When you are ready to remove the product from the box, refer to the installation

instructions.

TIP: Save your box and all packaging materials. They provide the only safe means of transporting/shipping the unit.

•

Ceiling Mount Evaporator Unit (Fan Coil Unit)

Accessory Kit:

•

(12) #14 2” Phillips Pan Head Screw

•

(1) 1/4” Drain Tube Connector

•

(1) 10 ft. 1/4” Drain Line

•

(1) 50’ Bottle Probe

•

(1) Remote Keypad

•

(1) 50’ Keypad Connection Cable

•

(1) Remote Box

•

(1) Split System Warranty Checklist

•

(2) Strain Reliefs

•

(1) Ceiling Mount Owner’s Manual

•

(1) Mounting Bracket

Check the Condenser Box for the following contents:

•

Ceiling Mount Condensing Unit

Accessory Kit Two:

•

(1) 1/4” Sight Glass

•

(1) 1/4” Filter Drier

•

(12) #8 x 3/8” Black Oxide Screws

•

(2) 7/8” Plugs

•

(1) Small Strain Relief

•

(2) Cable Ties

•

(2) Cable Tie Holders

•

(1) ∏” Plug

•

(1) Anti-Siphoning Device

Summary of Contents for 4000 Condenser



























































Search results

Summary of Contents for 4000 Condenser

Reviews:

Related manuals for 4000 Condenser

Brands by name

Popular brands

WhisperKool 4000 Condenser, Owner'S Manual

Search results

Summary of Contents for 4000 Condenser

Reviews:

Related manuals for 4000 Condenser

Brands by name

Popular brands