WhisperKool 4000 Condenser Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 58

background image

Page 16 | 1-800-343-9463

WCM

033114

INSTALLING THE EVAPORATOR UNIT WITH ATTIC ACCESS

PREPARING THE EVAPORATOR FOR INSTALLATION CONTINUED

12.

If you have purchased the Active Humidity Option, route the 1/4” water line out of the evaporator unit with the

drain line.

13.

Reinstall the protective caps on the end of the line set to prevent debris from entering the system.

14.

Reinstall the Top Access Panel and fasten the 16 screws into place.

15.

Secure the mounting bracket to the unit as outlined on the next page.

Note: It is highly recommended to use only the mounting locations provided. These locations ensure that the
installer will not drill into any copper or electrical within the system.

LINE SET

MOUNTING BRACKET

DRAIN LINE

POWER CABLE

WIRING

KNOCKOUT

BOTTLE PROBE &

KEYPAD WIRING

KNOCKOUT

«
...
16
17
18
19
20
...
»

Summary of Contents for 4000 Condenser



























































Reviews:

No comments

Related manuals for 4000 Condenser

Brand: Kaisai Pages: 168

Brand: Panasonic Pages: 72

Brand: Panasonic Pages: 36

mini VRF U-4LE2R5

Brand: Panasonic Pages: 60

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 149

Brand: RollSeal Pages: 44

Brand: York Pages: 4

Brand: eeese Pages: 94

Brand: ARCTIC WIND Pages: 16

Brand: point Pages: 60

23-11-2234N-001

Brand: Maytag Pages: 23

Brand: mabe Pages: 12

GWH18RC-K3DNA1A

Brand: Gree Pages: 92

Perfecto2 IRC5PO2W

Brand: Invacare Pages: 32

Brand: Technibel Pages: 47

bycool green line SLIM COOL TRR

Brand: dirna Bergstrom Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands