Whirlpool WSE 2930 W Manual Download Page 78

Page: 78 / 101

Troubleshooting

Alarm summery

Type

Buzzer

BLINKING ICON

RESET

Freezer door alarm

Yes (mute after 10 min)

Freezer door icon

Reset button

(Stop the buzzer)

Refrigerator door alarm

Yes (mute after 10 min)

Refrigerator door icon

Reset button

(Stop the buzzer)

Air filter alarm

Air filter icon

Reset button for 3 s.

(reset alarm)

Buzzer sound one time.

Water filter alarm

Water filter icon

Reset button for 3 s.

(reset alarm)

Buzzer sound one time.

Over temperature alarm

Yes (mute after 10 min)

Alarm icon

Reset button

(reset alarm and stop buzzer)

Long black out alarm

Yes (mute after 10 min)

Long black out alarm

Reset button

(reset alarm and stop buzzer)

Failure (any)

Yes (mute after 10 min)

Alarm icon

Reset button

(stop the buzzer)

Summary of Contents for WSE 2930 W






































































































Search results

Summary of Contents for WSE 2930 W

Reviews:

Related manuals for WSE 2930 W

Brands by name

Popular brands

Whirlpool WSE 2930 W, Manual

Search results

Summary of Contents for WSE 2930 W

Reviews:

Related manuals for WSE 2930 W

Brands by name

Popular brands