background image

2

SAVE THESE INSTRUCTIONS

Use only with type of gas approved for this furnace. 
Refer to the furnace rating plate. 

Install this furnace only in a location and position 
as specified in the “Location Requirements” section 
of these instructions.

Provide adequate combustion and ventilation air to 
the furnace space as specified in the “Venting
Requirements” section of these instructions.

Adequate clearance must be provided around the 
vent-air intake terminals.

Combustion products must be discharged outdoors. 
Connect this furnace to an approved vent system 
only, as specified in the “Venting Requirements” 
section of these instructions. 

Never test for gas leaks with an open flame. Use a 
commercially available soap solution made 
specifically for the detection of leaks to check all 
connections, as specified in the “Make Gas 
Connections” section of these instructions.

Always install furnace to operate within the furnace’s 
intended temperature-rise range with a duct system 
which has an external static pressure within the 
allowable range, as specified in the “Complete
Installation” section of these instructions. See 
furnace rating plate.

IMPORTANT SAFETY INSTRUCTIONS

When a furnace is installed so that supply ducts 
carry air circulated by the furnace to areas outside 
the space containing the furnace, the return air 
shall also be handled by duct(s) sealed to the 
furnace casing and terminating outside the space
containing the furnace.

A gas-fired furnace for installation in a residential 
garage must be installed as specified in the 
“Location Requirements” section of these 
instructions.

The furnace is not to be used for temporary heating 
of buildings or structures under construction.

The furnace shall be installed so the electrical 
components are protected from water.

■     

Furnaces for indoor installation on combustible 

         

flooring shall not be installed directly on carpeting, 

         

tile or other combustible material other than wood 

         

flooring. 

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or property 
damage.

— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or 

any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s 

instructions.

• If you cannot reach your gas supplier, call the fire department.

— Installation and service must be performed by a qualified installer, service agency or the gas 

supplier.

Summary of Contents for WFCT

































Reviews: