background image

Mounting and connecting the Control Box 

 

 

16 

1. 

Mount  the  control  box  (2)  with  suitable   
 screws and dowels for the resp. surface. 

Preferably mount the control box approx.   
150  cm  above  the  ground.  Make  sure   
the control box is not exposed to direct 
sunlight,  rain,  snow  or  direct  water  jet 
(high pressure water jet etc.). 

2. 

Unscrew  the  lock  nuts  of  the  strain 
relief and insert the power cable of the 
gate opener from below into the control 
box. Pull enough cable and tighten the 
lock nuts of the strain relief. 

 

The  cables  are  labelled  with  small  flags. 
Please  observe  the  flags  and  arrange 
them correctly. 

Order of the cables for Gate Opener 1: 

Red cable to +Motor1 

Black cable to 

–Motor1 

Red cable to ULT1 

Black cable to COM 

Yellow cable to DLT1. 

 

Order of the cables for Gate Opener 2: 

Red cable to +Motor2 

Black cable to 

–Motor2 

Red cable to ULT2 

Black cable to COM 

Yellow cable to DLT2. 

 

Please  also  observe  the  wiring  diagram  on 
the next page. 

Screws and 
dowels 
(not 
included) 

Opener 1 

Opener 2 

Summary of Contents for 18 39 13







































Reviews: