Section SDSĆ548Ć6LNĆ204
030Ć101328 Rev. A
R
0208I4RA
16
7.
CUSTOMER & TECHNICAL SERVICES
7.1
Customer Service & Technical Assistance
If technical or customer assistance is required, contact Westell
by calling or using one of the following options:
Voice: (630) 898Ć2500
Voice: (800) 323Ć6883
email:
Visit the Westell World Wide Web site at http://
www.westell.com
for additional information about Westell.
7.2
Part Numbers
This Westell equipment is identified by a model number and an
issue level. Each time a change is made to the product which
changes the form, fit, or function of the product, the issue level/
letter is incremented or advanced by one. Be sure to indicate the
issue level as well as the model number when making inquiries
about the product.
8.
WARRANTY & REPAIRS
8.1
Warranty
Westell warrants this product to be free of defects at the time of
shipment. Westell also warrants this product to be fully funcĆ
tional for the time period specified by the terms and conditions
governing the sale of the product. Any attempt to repair or
modify the equipment by anyone other than an authorized WesĆ
tell representative will void the warranty.
8.2
Repair and Return
Westell will repair or replace any defective Westell equipment
without cost during the warranty period if the unit is defective
for any reason other than abuse, improper use, or improper
installation. Before returning the defective equipment, first reĆ
quest a Return Material Authorization (RMA) number from
Westell. Once an RMA number is obtained, return the defective
unit, freight prepaid, along with a brief description of the probĆ
lem, to:
Westell, Inc.
ATTN: R.G.M. Department
750 N. Commons Drive
Aurora, IL 60504Ć7940
Replacements will be shipped in the fastest manner consistent
with the urgency of the situation. Westell will continue to repair
or replace faulty equipment beyond the warranty period for a
nominal charge. Contact Westell for details.
9.
SPECIFICATIONS
9.1
Ordering Specifications
To order units, call the telephone numbers shown in Paragraph
7.1,
and please specify a specific model number shown in
Table 10.
Part/Model #
Description & Comments
SDS5486LN
CLEI Code: DST1KDN1AA
INTELIPORT LN" (Issue 4)
Technical Publication
030Ć101328
*CLEI is a trademark of Telcordia Technologies.
Table 10. Ordering and Option Information
9.2
Electrical and Physical Specifications
The electrical and signaling specifications are listed below, and
the physical specifications for the SDS5486LN are shown are
shown in Table 11.
A.
RCV Level Range: Input, Ć10 to +5.0 dBm (TLP) or Ć23
to Ć8.0 dBm (DLP); Output, Ć3.0 dBm (TLP), Ć16.0 dBm.
B.
XMT Level Range: Input, +13 dBm (TLP) or 0 dBm
(DLP); Output, +5.0 dBm (TLP) or Ć8.0 dBm (DLP).
Ć NOTE Ć
XMT OUT level can be adjusted (in 0.5 dB gain/loss
increments) for any level from +7.0 to Ć16.0 dBm
(TLP) or Ć6.0 to Ć29 dBm (DLP)
C.
Impedance: FacilityĆside, selectable for 150, 600, 1200
Ohms via option switch S2; EquipmentĆside (2W/4W),
600 Ohms, fixed.
D.
Test Mode: Activated by pressing frontĆpanel TEST
switch (<5 sec); Applies 1014 Hz to transmission ports
when activated (see Table 4); Equipped with automatic
release of one hour if switch not pressed a second time;
TEST switch can also be used to activate INTELIPORT's
AUTOĆALIGN feature by pressing switch for >5 sec and
only during first five minutes of initial powerĆup.
E.
Command Mode: Activated by sending 2713 Hz (>30
sec). INTELIPORT returns 1014 Hz at +5dBm (TLP)
indicating command mode initiation. NOTE: If 2713 Hz
is removed in <30 sec, INTELIPORT sends alternating
1014 Hz/414 Hz tone and enters loopback.
F.
Equalization: Automatically provides RCV channel amĆ
plitude equalization (up to 15dB, re: 1004 Hz) to meet
C5 conditioning.
G.
Remote Alignment: Aligns to 3 or 4 tones, at TLP; ActiĆ
vated from command mode by sending 1004Hz in
response to INTELIPORT's 1014Hz (see para. 3.13
through 3.16 for details).
H.
AutoĆAlign: Automatically aligns to 4 tones, at TLP; AcĆ
tivated by pressing the frontĆpanel TEST switch (>5 sec)
