47
C
ABINET
41
NOTE:
Tighten screws snugly, but do not over tighten (use special care with a power screwdriver).
P
REASSEMBLE
M
ISCELLANEOUS
P
ARTS
Top Panel
1. Place the top panel (#20) flat, with the outside surface up.
2.
See Detail A
.
Use a plastic mallet to pound 1/4-20x5/8 screw inserts (#9 oyster) into the 10 holes located on the outside surface of
the top panel.
Left and Right Back Panels
3. Place the right and left back panels (#21 and 22) flat, with their outside surface up.
4. Use a plastic mallet to pound
1
/
4
-20 x
5
/
8
screw inserts (#9 oyster) into the
3
/
8
” holes located on the left side panel and the
three
3
/
8
” holes located on the right side panel.
5. Use a plastic mallet to pound 8-32 x
7
/
16
screw inserts (#10 oyster) into the eight
1
/
4
” holes located on the left side panel.
6. Insert wood dowels (#6) into the three holes on the top edge of each of the back panels (#21 and 22).
7. To protect corners and edges while moving the cabinet into place, push or hammer plastic tack glides (#13, not shown) into the
bottom edge of the side panels, about 2" from the corners.
Right Side Panel
NOTE:
The left and right side panels have a notch in the bottom front corner.
8. Place the right side panel (#23) flat, with the outside surface up.
9. For fixed shelf option only, use a plastic mallet to pound 1/4-20x5/8 screw inserts (#9 oyster) into the (43) 3/8” holes.
10. For fixed shelf option only, use a plastic mallet to pound 8-32x7/16 screw inserts (#10 oyster) into the (8) 1/4” holes.
11. Turn the right side panel over so the outside surface is facing down.
12. Insert wood dowels (#6) into the 3 holes close to the top edge of the side panel.
13. To protect corners and edges while moving the cabinet into place, push or hammer plastic tack glides (#13, not shown) into the
bottom edge of the side panel, about 2" from the corners.
Left Side Panel
NOTE:
The left and right side panels have a notch in the bottom front corner.
14. Place the left side panel (#24) flat, with the outside surface up.
15. Use a plastic mallet to pound
1
/
4
-20 x
5
/
8
screw inserts (#9 oyster) into the four
3
/
8
” holes.
16. Use a plastic mallet to pound 8-32 x
7
/
16
screw inserts (#10 oyster) into the twelve
1
/
4
” holes.
17. Turn the right side panel over so the outside surface is facing down.
18. Insert wood dowels (#6) into the three holes close to the top edge of the side panel.
19. To protect corners and edges while moving the cabinet into place, push or hammer plastic tack glides (#13, not shown) into the
bottom edge of the side panel, about 2" from the corners.
A
SSEMBLE THE
M
AIN
P
ANELS
NOTE:
At least two people are required to assemble the cabinet.
20. Place the right (#23) and left (#24) back panels vertical with the tack glides on the bottom.
21. Connect the left and right back panels together with five hex-socket lag screws (#2 oyster).
22. Attach the right side panel to the assembly and connect with five hex-socket lag screws (#2 oyster). Allow the head of each lag screw
to extend
1
/
2
” from the surface.
23. Attach the left side panel to the assembly and connect with five hex-socket lag screws (#2 oyster). Allow the head of each lag screw
to extend
1
/
2
” from the surface.
24. Place the top panel (#20) onto the assembled panels, aligning the installed wood dowels (#6) in the holes in the top panel (#20).
25. Tighten the ten hex-socket lag screws (#2 oyster) in the side and back panels.
26.
See Detail K
.
Attach the top panel to the assembly with twelve hex-socket lag screws (#2 oyster).
27. Slip the two toe kick extrusions (#59) onto the front edge of the toe-kick area of the side panels, and secure each with a 1
1
/
4
" painted
pan-head screw (#14).
28. Attach the upper frame assembly (#54) to the inside of the top panel using six hex-socket screws (#56) and to the side panels
using two hex-socket screws (#56) on each side.
29.
See Detail F
.
Fasten five leveler glides (#51) and weld nuts to the bottom frame assembly (#55) Tighten the leveler glide until the
head is tight against the weld nut and drive a tube plug (#57) into both open ends of the bottom frame assembly.
30. Attach the bottom frame assembly (#55) to the inside of the back panels using three hex-socket screws (#56 oyster) on each back
panel, and to the side panels using two hex-socket screws (#56) on each side.
L
EVEL THE
C
ABINET AND
M
AKE
F
INAL
A
DJUSTMENTS
31. Move the cabinet to its intended location, and level it by using a
1
/
4
" socket or wrench. Refer to the leveling procedure on page 58.
32. To attach doors, refer to pages 59 - 67.
33. To attach two or more cabinets together, and to secure the cabinet(s) to the back wall, refer to pages 68 - 70.
34. If the cabinet is to be free-standing, it is advisable to use suitable floor-anchoring fasteners to hold the side panels stationary.
Be sure that the cabinet is square and plumb before anchoring.
I
NSTALLING
A
CCESSORIES
35. To install any hanger or shelving options, refer to the additional assembly instructions that were sent with the storage option.
