manualshive.com logo in svg

Wenger Gearboss Customizable Wood Lockers, Installation And Owner'S Instructions, Page: 23 / 28

Share
Download
Wenger Gearboss Customizable Wood Lockers Installation And Owner'S Instructions Download Page 23

23

Optional Side Closure Panel Accessory Installation for 

Lockers without Metal Base

Side closure panels can be installed on lockers with or without a metal base.

 

This is the procedure for installing without a metal base!

 

For installing on lockers with a metal base, go to page 21.

STOP

Assembly

1.  Carefully remove the end cover panel from the package. 
2.  Pound two plastic tack glides (23) into the bottom edge, centered and 2"-3" from each end.
3.  Attach one toe kick cover plate (24) to the bottom notched edges of the end cover panel using  

two #8-15 x 1-1/4" truss head screws (25).

 

Single end cover panels (17) use one cover plate. 

Island end cover panels (17) use two cover plates.

4.  If attaching a single end cover panel, continue to the following page. 

If attaching an island end cover panel, skip to page 25.

Toe Kick 

Cover Plate  

(24)

#8 x 1-1/4"  

Truss Head Screws 

(25)

Island End  

Cover Panel 

(17)

Single End  

Cover Panel 

(17)

2"-3"

Tack 

Glides 

(23)

Pound in 

Tack Glides

Summary of Contents for Gearboss Customizable Wood Lockers





























Reviews:

No comments