manualshive.com logo in svg

Wenger Gearboss Customizable Wood Lockers, Installation And Owner'S Instructions, Page: 19 / 28

Share
Download
Wenger Gearboss Customizable Wood Lockers Installation And Owner'S Instructions Download Page 19

Secure to Structure (Wall Mount Configurations Only)

 

Important:  Procedure is the same for lockers with or without metal base.

1. 

A

ttach the lockers to the wall.

a.  Straddle a locker spacer bracket (7) at the top rear of two adjoining lockers.
b.  Attach the locker spacer bracket to the  

back wall using the appropriate  

fasteners and method described  

in the "Fasteners - Not Suppled"  

section.

 

Note:  

If the wall is not  

          straight, it may be  

          necessary to add shims  

          behind some of the  

          locker spacer brackets.

c.  Attach the locker spacer  

bracket to both lockers  

using two #10-16 x 3/4"  

pan head screws (14).

d.  Attach the remaining  

wall mount lockers to  

the back wall.

19

#10-16 x 3/4" 

Pan Head Screw 

(14)

Attach to the wall

Locker Spacer 

Bracket 

(7)

Secure Lockers to the Structure

This procedure is for securing wall mount lockers to the structure.

 

See the following page for securing island mount lockers to the structure.
This instruction is for standard installation only. 

 

See separate seismic instructions if required.

STOP

In addition to the sides of the lockers being secured, 

the locker backs must also be attached to a back wall.

Inferior or improperly installed fasteners 

could cause the lockers to tip over.

!

CAUTION

!

WARNING

Summary of Contents for Gearboss Customizable Wood Lockers





























Reviews:

No comments