manualshive.com logo in svg

Wenger Gearboss Customizable Wood Lockers, Installation And Owner'S Instructions, Page: 20 / 28

Share
Download
Wenger Gearboss Customizable Wood Lockers Installation And Owner'S Instructions Download Page 20

20

Secure Lockers to the Structure (continued)

This procedure is for securing island mount lockers to the structure.

 

See the previous page for securing wall mount lockers.
This instruction is for standard installation only.

 

See separate seismic instructions if required.

STOP

Secure to Structure (Island Mount Configurations Only)

 

Important:  Procedure is for lockers without metal base only.

Because materials and construction of walls can vary, fasteners for attaching the lockers to the structure  

are not provided. The installer must choose the appropriate fastener and follow the manufacturer's instructions.  

See "Fasteners - Not Supplied" on page 5 for more information.

Note:  

The end of every locker bank must be secured to the floor.

Note:  

Make sure all the lockers are secured together before attaching them to the floor.

1.  At the ends of the locker bank, attach one cabinet connector bracket (21) to the bottom inside of each  

locker using a minimum of two #8 x 5/8" pan head screws (22).

 

The brackets have extra holes for the best fit.

2.  Secure the bracket to the floor using the 

 

appropriate fasteners.

3.  Reattach any bottom shelves that  

were removed during installation.
a.  Slide the shelf in.
b.  Reattach the four screws to  

secure the shelf to the locker.

In addition to the sides and backs of the lockers being 

secured, the lockers must also be attached to the floor.

Attach to the locker  

using #8 x 5/8"  

Pan Head Screws 

 

(22)

Cabinet Connector 

Bracket  

(21)

Inferior or improperly installed fasteners 

could cause the lockers to tip over.

!

CAUTION

!

WARNING

Slide 

shelf in

Reattach 

screws

Summary of Contents for Gearboss Customizable Wood Lockers





























Reviews:

No comments