background image

ENGLISH

GAS APPLIANCE CODE COMPLIANCE 
 

The installation of gas piping from the outlet side of the gas meter or 
service regulator to the charbroiler must be performed by a technician  
qualified and certified or licensed to install gas-fired equipment. 
 
A licensed and qualified technician must perform the initial startup and 
adjustment of this appliance.

 

 
The installation of this gas-fired appliance must conform to local codes, 
or in the absence of such codes, with the current edition of 
National Fuel Gas Code ANSI Z223.1. 
 
For use in the State of Massachusetts, this appliance must be installed 
in compliance with 

Massachusetts Fuel Gas and Plumbing Code 

CMR 248. 

 
The installation of this gas-fired appliance must comply with 
applicable portions of NFPA 96 for ventilation.  The current edition of 
NFPA 96 (

Standard for the Installation of Equipment for the Removal   

of Smoke and Grease Laden Vapors from Commercial Cooking     
Equipment

) specifies ventilation requirements to ensure the removal    

of exhaust gasses and products of combustion. 
 
 
IT IS THE RESPONSIBILITY OF THE INSTALLER TO ENSURE   
THAT THIS GAS BROILER INSTALLATION CONFORMS TO ALL   
APPLICABLE CODES AND ORDINANCES. 
 
The venting of this appliance must not be obstructed, nor may such 
venting interfere with the flow of combustion air required for proper     
operation of the gas burners. 
 
Additionally: 

 
1. 

The gas supply line used to connect the appliance to the gas 

 

supply system must be black iron pipe, or other material as  

 

approved by local ordinance for gas piping. 

 
2. 

Gas supply piping must be 3/4” inside diameter or greater. 

 
3. 

Use pipe sealant made specifically for gas piping on all pipe 

 

joints.   

Apply sealant sparingly to the male threads only. 

 

Sealant must be resistant to the action of LP gas.  

 
4. 

Verify that all supply piping is clean and free of obstructions, dirt, 

 

chips and pipe sealant compound prior to installation. 

 
5. 

All pipe joints must be checked for leaks before lighting.  Leak 

 

checks should be performed with a soap and water solution.  

 

NEVER CHECK FOR LEAKS WITH AN OPEN FLAME. 

 

6. 

This appliance must be installed so that there is adequate and 

 

proper clearance for operation and servicing. 

 
 

INSTALLATION (continued) 

DANGER: 

FIRE AND 
EXPLOSION 
HAZARD 

NEVER use an open flame to 
check for gas leaks.  Fire and 
explosion may result. 

 

 

WARNING: 

RISK OF  INJURY 

 

Installation procedures must 
be performed by a qualified 
technician with full knowledge 
of all applicable gas-fired    
appliance codes.  Failure can 
result in personal injury and 
property damage. 
 

IMPORTANT: 

All pipe joints must be 
checked for leaks before 
lighting.  Leak checks should 
be performed with a soap and 
water solution. 
 

IMPORTANT: 

Information on the 
construction and installation 
of ventilating hoods may be 
obtained from the current 
edition of NFPA 96 

Standard for the Installation 
of Equipment for the Removal 
of Smoke and Grease Laden 
Vapors from Commercial 
Cooking Equipment

.  

Copies of this standard are 
available from the 
Nation Fire Protection Assn.: 
 
NFPA 
1 Batterymarch Park 
P.O. Box 9101 
Quincy, MA 02269-9101 

164 

  307

737 

 OpM

anual 

fo

r HDCR-Series Char-Rock Broi

lers

 

Summary of Contents for HDCR-1230G































Reviews: