Well Bubbler 10-120 Installation And Configuration Manual Download Page 31 | Manualshive

Page: 31 / 32

Well Bubbler 10-120 Installation And Configuration Manual Download Page 31

THE WELL BUBBLER

WWW.WELLBUBBLER.COM

CONFIGURATION: FIRMWARE, SPECIFICATIONS

The Firmware Version is displayed for reference only; please include it when contacting
Well Bubbler support.

The specific gravity parameter is set at the factory, and can be changed via the Manager
software utility, or remotely, for Well Bubblers with cellular monitoring. This value is set
to 1.000 by default, for measuring pure water. The Well Bubbler can also be used to
measure a variety of liquids, such as acid, fertilizer and sludge, with different densities
and specific gravity values.

The rating of a Well Bubbler is set at the factory, and should not be changed afterwards.
Well Bubblers with relatively low ratings of  15 psi, 30 psi and 50 psi are available for
accurate measurement of  tank and reservoir levels, and shallow wells. Pressure ratings
of  150 psi, 200 psi and 300 psi are used for monitoring deep wells.

DRAWN BY: A. BUGROV

DATE: 02.20.2021

PAGE: 31

«
...
29
30
31
32
»

Summary of Contents for 10-120

































Reviews:

No comments