Welker INFLOW Installation, Operation And Maintenance Manual Download Page 35

Page: 35 / 41

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Reassembly

68.

Carefully slide the insertion cylinder onto the lubricator body.

69.

Coat the inside of the top end of the insertion cylinder with lubricant. The bottom of the insertion cylinder can be

identified by its vent port.

70.

Lightly lubricate the outer shaft.

71.

Slide the outer shaft into the lubricator body.

72.

Carefully slide the top cap onto the top end of the outer shaft and down to the insertion cylinder.

73.

As necessary, install the tie bolts following a cross-bolting sequence (

Figure 19

Figure 19: Cross-Bolting Sequence

74.

Install the four (4) alignment nuts and the four (4) heavy hex nuts to the tie bolts so that the lock collar can later be

secured to the top cap (

Figure 20

). Location of the four (4) alignment nuts is critical.

Figure 20: Correct Alignment Nut Installation

75.

Following a cross-bolting sequence, tighten the alignment nuts and heavy hex nuts to the appropriate torque (

Figure 19

Figure 20

, and

Table 2

Table 2: Torque Specifications for Tie Bolts

Tie Bolt Diameter

Foot-Pounds (ft•lb)

Kilograms per Meter (kg/m)

½"

15–20

2.07–2.76

76.

Carefully slide the lock collar onto the outer shaft, and then tighten the lock collar cap screws.

77.

With the upper housing assembly attached to the insertion shaft, insert the insertion shaft into the outer shaft.

78.

Screw the outer shaft into the packing gland body, and then tighten the setscrews in the base of the packing gland

body to secure the upper housing assembly to the outer shaft.

79.

Insert the purge tube into the insertion shaft, and then screw the purge assembly into the insertion shaft.

Summary of Contents for INFLOW










































Search results

Summary of Contents for INFLOW

Reviews:

Related manuals for INFLOW

Brands by name

Popular brands

Welker INFLOW, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for INFLOW

Reviews:

Related manuals for INFLOW

Brands by name

Popular brands