Welker INFLOW Installation, Operation And Maintenance Manual Download Page 40

Page: 40 / 41

Inlet Sand Relief

12.

Unscrew the relief cap from the cylinder base to expose the inlet sand relief.

13.

Examine the seat of the inlet sand relief for damage or wear. Replace as necessary.

14.

As necessary, replace the O-rings on the seat of the inlet sand relief.

15.

Examine the spring of the inlet sand relief for damage or wear. Replace as necessary.

16.

Examine the poppet of the inlet sand relief for damage or wear. Replace as necessary.

Reassembly

17.

Insert the inlet sand relief into the cylinder base, and then screw the relief cap onto the cylinder base.

18.

Screw the cylinder base with relief cap onto the collection head.

19.

Insert the internal sand relief into the piston.

20.

If performing full maintenance on the inFlow™ ACE, set the collection head aside and continue to the next step in

Section 3.2, Maintenance

. If maintenance is only being performed on the collection head, screw the piston onto the

insertion shaft, and then screw the collection head onto the outer shaft. Tighten the jam nut to lock the collection head

in place. For maximum sample volume, ensure that the bottom of the jam nut is flush with the bottom of the outer shaft.

21.

Connect a safety wire from the opening in the relief cap to the jam nut. Ensure that the safety wire is wrapped in a

counterclockwise rotation to prevent the associated threads from unscrewing from each other.

If a replacement safety wire is not available, ensure that the relief cap is securely tightened so that it can withstand the pressure

of the flowing stream.

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Summary of Contents for INFLOW










































Search results

Summary of Contents for INFLOW

Reviews:

Related manuals for INFLOW

Brands by name

Popular brands

Welker INFLOW, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for INFLOW

Reviews:

Related manuals for INFLOW

Brands by name

Popular brands