Welker INFLOW Installation, Operation And Maintenance Manual Download Page 32

Page: 32 / 41

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Reassembling the Upper Housing

42.

Carefully slide the external adjustment body onto the insertion shaft. The lock collar grooves in the insertion shaft should

be accessible on both sides of the external adjustment body.

43.

Install the lower lock collar to the groove below the external adjustment body and align the pin hole in the lock collar

with the pin in the external adjustment body.

The lower lock collar must be installed to the insertion shaft assembly before the upper lock collar.

44.

Install the upper lock collar to the groove above the external adjustment body and align the pin hole in the lock collar

with the pin in the external adjustment body.

45.

Tighten the setscrews in the upper and lower lock collars to secure the adjustment assembly to the insertion shaft.

46.

Carefully insert the insertion shaft assembly through the packing gland body, taking care not to scratch the shaft.

47.

Slide the gland cover onto the packing gland body, and then return the plug to the lubrication port.

48.

Slide the dustcover onto the packing gland body.

49.

Carefully slide the motor housing onto the insertion shaft, taking care not to scratch the shaft.

50.

Carefully screw the motor housing into the packing gland body.

51.

Return the top cap to the top of the insertion shaft and carefully slide the top cap down to the motor housing.

52.

Bolt the top cap in place.

53.

Set the upper housing and insertion shaft assembly aside.

Summary of Contents for INFLOW










































Search results

Summary of Contents for INFLOW

Reviews:

Related manuals for INFLOW

Brands by name

Popular brands

Welker INFLOW, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for INFLOW

Reviews:

Related manuals for INFLOW

Brands by name

Popular brands