Welker INFLOW Installation, Operation And Maintenance Manual Download Page 34

Page: 34 / 41

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Lubricator Body Maintenance

Figure 18: Lubricator Body Detail

61.

With the collection head and upper housing removed, carefully pull the outer shaft out of and the insertion cylinder off

the lubricator body. As necessary, remove the tie bolts.

62.

Inspect the insertion cylinder for scratches or damage. If scratches or damage are present, repair or replace as necessary.

63.

Closely inspect the polished outer diameter of the outer shaft. Scratches or pits may cause the seals to leak. If scratches

or pits are present, the unit may need to be repaired or replaced. Contact Welker for service options.

64.

Inspect the shaft bearing in the outer shaft. Replace it if it shows signs of wear or damage.

65.

Replace the U-cup in the outer shaft. The U-cup should be installed so that the "U" is open to the product pressure.

66.

Replace the O-rings, back ups, and Stat-O-Seal® in the lubricator body.

67.

Inspect the lubricator bushing in the lubricator body. Replace it if it shows signs of wear or damage.

Summary of Contents for INFLOW










































Search results

Summary of Contents for INFLOW

Reviews:

Related manuals for INFLOW

Brands by name

Popular brands

Welker INFLOW, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for INFLOW

Reviews:

Related manuals for INFLOW

Brands by name

Popular brands