14
15
06.05.2022
EN
EN
1.
Control panel
2. Handles
3.
Welder power cord
4.
Welder on / off button
5. Fan
6.
Gas connection
7.
Socket (+)
8.
TIG torch control socket / Control pedal socket
9.
Gas socket
10. Socket (-)
11. Radiator on / off button
12. Radiator water level indicator
13. Undercarriage with wheels
14. Water outlet
15. Radiator outlet
16. Radiator inlet
17. Radiator water filler
18. Radiator power cord
CONTROL PANEL DESCRIPTION (BOTH MODELS)
A.
MMA / TIG mode switch
B. LED
B1. MMA active mode
B2. TIG active mode
C. Display
D.
LED – the unit of currently displayed value
E.
LED - error, thermal overload
F. LED - pedal control (activates automatically after
connecting the pedal)
G.
Shift to the left when choosing a parameter to set /
save parameters after holding for 3s
H.
LED - saving parameters
I.
LED - loading saved parameter values
J.
Shift to the right when choosing a parameter to set /
load saved parameters after holding for 3s
K.
LEDs - show the type of parameter being displayed:
•
Pre Flow - gas pre-flow time
• Start Amps - output current after arc ignition
• Up Slope - time of current intensity increase
• Peak Amps - peak current
• Peak On Time - ratio of the peak current pulse
duration to the base current pulse
2
17
15
16
7
8
11
12
13
10
9
1
4
3
5
6
18
14
A
C
B
D
E
C
B
A
1
3
4
5
6
2
1.
Cap, long
2.
Cap, short
3. Collet
4.
Torch handle
5.
Collet inside housing
6.
Ceramic nozzle
TIG TORCH
ENTRIX 315AW
A.
cable with TIG holder
B. workpiece
C.
ground wire
D.
pressure regulator
E.
gas cylinder
CONNECTION DIAGRAM - MMA WELDING MODE
ENTRIX 315A
D
E
C
A
B
ENTRIX 315AW
PLEASE NOTE!
The illustrations of this product can
be found on the last page of the instruction manual
(pp. 44).
• Base Amps - base current supporting the arc
• Pulse Frequency - pulse frequency during welding
• AC Balance
• AC Frequency
• Down Slope - time of current descent
• End Amps - value of output current before the end
of welding.
•
Post Flow – gas post-flow time
L.
2T / 4T mode switch
M. LED
M1. 2T mode - pressing the button on the burner
initiates the welding process, releasing the button
ends the process
M2. 4T mode - pressing the button on the burner
initiates the welding process, releasing the button
does not end the process. Pressing and releasing the
button again ends the welding process.
N.
Value adjustment knob (press the knob for rough
adjustment)
O.
Pulse / No Pulse mode switch
P. LED
P1. Pulse mode
P2. No Pulse mode
Q.
AC / DC switch
R. LED
R1. AC mode
R2. DC mode
5.1. PREPARING THE DEVICE FOR USE / DEVICE USE
Each unit is equipped with a main power cable, which
is responsible for providing current and voltage to the
device. If the device is connected to power which exceeds
the required voltage, or if the wrong phase is set, it may
lead to severe damage to the unit. This is not covered
by the warranty for the equipment and the user will be
responsible for such situations.
5.2. DEVICE USE
Before welding, properly connect the welding cable and
other parts depending on the mode (TIG or MMA); follow
the drawings below.
CONNECTION DIAGRAM - TIG WELDING MODE
ENTRIX 315A
C
B
A
ENTRIX 315AW
A.
cable with electrode holder
B. workpiece
C.
ground wire
Device operation
1.
Connect the device to a power source and turn it on
by pressing the On / Off button. „LL“ will appear on
the display.
2. Set the welding mode using the mode selection
buttons (A), (L), (O) and (Q).
3.
Set welding parameters for a given mode (settings are
available only for the selected MMA or TIG mode, the
rest is inactive):
• use the (G) or (J) menu button to move left / right
between the parameters; set the parameter values
using the (N) knob.
• to save the selected parameters in the
device‘s memory, press and hold the (G) button
for about 3 seconds, the display will show „P01“,
the (H) LED will light up. Use the (N) dial to select
one of the memory positions (P01 to P10) and
press the Menu (G) button again. The (H) LED will
go off, the parameters have been saved
• to load the previously saved welding parameters,
press and hold the (J) button for approx. 3 seconds.
„P01“ will appear on the display and the (I) LED
will light up. Use the (N) knob to select a memory
position, then press the Menu (J) button again,
the (I) LED will go out, the parameters have been
loaded.
4.
Wenn der Thermoschutz aktiviert ist, erscheint auf der
Anzeige "Err" und die Diode (E) leuchtet. Lassen Sie
das Gerät abkühlen und beseitigen Sie, wenn möglich,
die Ursache der Überhitzung.
5.
Operation mode with foot pedal. After connecting the
foot pedal to the (8) socket on the welder, the device
will automatically switch to REM mode, the (F) LED
will light up. In the REM mode, the peak current (Peak
Amps) is controlled with the foot pedal.
When starting to weld with the device in TIG mode, follow
the instructions below:
LIFT TIG WELDING MODE
1.
Select the TIG welding function on the control panel
(8).
