Webasto Transit Vancouver Wagon Manual Download Page 31 | Manualshive

Page: 31 / 44

background image

Ford Transit

Vancouver

31

21. Remove the factory HVAC duct, if applicable.

Using the board bracket kits (46), install the basic
and extreme circuit boards (44, 45) above the side-
curtain air bags using self-tapping screws.

22. Replace one of the 60 amp fuses with the

supplied 70 amp fuse (71). Reinstall the power
distribution center at this time.

23. Connect the positive wire to the fuse installed

earlier. Connect the ground wire to a good ground
point. Route and secure the wiring to prevent
chaffing.

«
...
29
30
31
32
33
...
»

Summary of Contents for Transit Vancouver Wagon













































Reviews:

No comments

Related manuals for Transit Vancouver Wagon

Brand: Mazda Pages: 4

Brand: Abicor Binzel Pages: 8

Brand: Quincy lab Pages: 4

Brand: Napoleon Pages: 4

Brand: Napoleon Pages: 4

Brand: Napoleon Pages: 2

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

Brand: Parrot Pages: 11

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

Brand: Vega Pages: 2

Brand: Vega Pages: 11

KO PROPO RTF 2002 ESC

Brand: Tamiya Pages: 2

Brand: probrake Pages: 2

Brand: Burley Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands