Tools Needed:
37
Please Do Not Return This Product To The Store.
Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the
Find a Dealer
section online at
www.Wayne-Dalton.com
If the system is activated, follow these
steps to reset the system:
3. Clamp vice grips on both vertical tracks
just below the bottom section.
4. Flip the pawl knob on both end brackets
to the upper position (see illustration).
5. With assistance, raise the door slightly
to reset the system.
IMPORTANT:
BE PREPARED TO SUPPORT
THE TOTAL WEIGHT OF THE DOOR.
6. Cautiously remove the vice clamps from
the vertical tracks; with assistance, lower
the door.
IMPORTANT:
BE PREPARED TO HOLD THE
FULL TENSION OF THE SPRING.
7. Check for spring tension. Starting on the
right hand side, place a ratchet and 5/8”
socket on the Torquemaster® Plus end
bracket (see illustration). Ensure ratchet is
set so that it will tighten counter clockwise
on the right hand side, and clockwise on
the left hand side (if applicable). If ten-
sion is present, remove the ratchet and
check the left hand side (if applicable). If
spring(s) have tension, proceed to Step
8; if no spring tension is present, contact
a qualified door agency to replace the
spring(s).
NOTE:
A 3” extension is also
recommended for added clearance from
the horizontal angle.
8. Lift door and check its balance. Adjust
spring(s), if door lifts by itself (hard to pull
down) or if door is difficult to lift (easy to
pull down). Anytime spring adjustments
are made, pawl knob must be in the upper
position (see illustration).
An unbalanced door such as this can
cause idrive® or Torquemaster® opera-
tion problems. To adjust spring(s), only add
or remove a maximum of 3/10 of a turn
(three teeth of ratchet wheel) at a time.
Both sides need to be adjusted equally on
double spring doors.
PLACE VICE CLAMPS
BELOW BOTTOM SECTION
ON BOTH VERTICAL TRACK
PAWL KNOB IN LOWER
POSITION
PAWL KNOB IN UPPER
POSITION
LOWER POSITION
UPPER POSITION
Cab
le Dr
um
No sp
ace betw
een Ratc
het
Pawl an
d Cabl
e Dr
um
indica
tes engageme
nt
Cabl
e Dr
um
Ratch
et Paw
l
ENGAG
ED SID
E VIEW
No sp
ace betwe
en
Ratchet P
awl and
Cabl
e Dr
um
ENGA
GED
UNDE
RNE
ATH
VIEW
Space
betwee
n Ratch
et Pa
wl
and
Cable
Drum
non-in
dica
tes engag
ement
Cabl
e Dr
um
Ratche
t Paw
l
DISENGA
GED
SIDE VIEW
No sp
ace
betwee
n
Ratche
t Paw
l and
DISENGA
GED
UNDE
RNE
ATH VIEW
UPP
ER POSIT
ION
LOWER POSIT
ION
LOWER POSIT
ION SIDE
VIEW
UPP
ER POSIT
ION SIDE
VIEW
Ratche
t Pawl in
Lowe
r Posi
tion
Ratche
t Paw
l in Upper Pos
ition
Use
these Illus
tration
, in conj
uncti
on wi
th th
e Instruction
s on
the other si
de of
this label.
WAR
NING
Rachet Bracke
t is under
EXTREME SPRING
TENS
ION
.
To avoid
possible sev
ere or
fatal injury
,
DO NO
T
remove
fasteners
from
ratchet
bracket
until spr
ing(s) are
fully
wnwound
.
To safely unwind spr
ing(s)
read
and fo
llow the dire
ctions in the
installati
on instructio
ns/owners
manual
.
DO NO
T REMOVE
THIS
TAG
.
RATCHET
WITH 5/8”
SOCKET
END BRACKET
3” EXTENSION
TorqueMaster® Plus Reset
Instructions Continued...
PAWL
INST
ALLA
TION