Waterworld new millenium Installation & Service Manual Download Page 3

1

Please read this entire service guide prior to beginning installation.  

REVERSE OSMOSIS SYSTEM WITH BUILT IN PUMP

Congratulations on choosing the Millennium Reverse Osmosis System.  Our high quality reverse 

osmosis system has been designed and tested to give you trouble free performance for many years 

with proper maintenance.  Please carefully read through this manual before installing the system.  

Make yourself familiar with all the parts, components, and installation procedures before continuing.

The Millennium unit is equipped with a pressure booster pump for the membrane.  This is required 

where feed pressure is below 40 PSI, but higher than 5 PSI. It is also useful when higher production 

rates are required.  This system is also equipped with a high and low pressure switch to operate and 

protect the pump.

CAUTION: ALWAYS CONSIDER ELECTRICAL SHOCK HAZARD WHEN WORKING WITH AND 

HANDLING ELECTRICAL EQUIPMENT. IF UNCERTAIN, CONSULT AN ELECTRICIAN. ELECTRICAL 

WIRING SHOULD ONLY BE DONE BY A QUALIFIED ELECTRICIAN PER LOCAL AND STATE  

ELECTRICAL CODES.

Before installing you will need to make sure that you have a dedicated power supply under the 

sink, or within 4 feet of the system.  We highly recommend a GFI outlet to plug the unit into as this 

system is usually located near numerous water supplies.  Follow all electrical and plumbing codes 

and be certain of the voltage requirements on the Millennium unit. For installation assistance, contact 

your local dealer. 

We have supplied the system with Color coded tubing for ease of installation.

The following tools will be required for your installation:v

1)  Hand drill for faucet hole.  Use the appropriate bit for the surface you are drilling. (½” for non 

air gap faucets and - 7/8” drill bit for air gap ones).

 

A)  Titanium bit for metal sinks.

 

B)  Glass and tile bit or Relton cutter for porcelain sinks.

 

C)  Diamond core bit for granite.

2)  Phillips head screwdriver.
3)  Adjustable crescent wrench.
4)  Basin wrench.
5)  ¼” drill bit for drain clamp.

Your local dealer

Summary of Contents for new millenium

















Reviews: