Waterworld new millenium Installation & Service Manual Download Page 16

14

Millennium

®

 LIMITED WARRANTY

The Millennium

®

 reverse osmosis system is warranted to be free from defects in materials and workmanship under normal 

use within the operating parameters listed below. For a period of five years from the date of purchase Millennium

®

 will 

repair or replace any part of the reverse osmosis system with the exception of the filters and electrical components (pump, 

transformer and switches are only covered for one year).

CONDITIONS OF WARRANTY:

Factory assumes no responsibility for incidental or consequential damages; for damages arising out of misuse of the prod-

uct or the use of any unauthorized attachment; for damages resulting from improper installation or for damages resulting 

from the use of the product with a defective plumbing system.

In no event shall the factory be liable for any direct, indirect, special, punitive, incidental, exemplary or consequential dam

-

ages, attorney’s fees or any damages whatsoever, even if Millennium® has been previously advised of the possibility of 

such damages, whether in an action under contract, negligence, or any other theory, arising out of or in connection with 

the use, inability to use, or performance of the Millennium® system.

Factory is not responsible or liable for damage to any part of the Millennium® system because of misuse; misapplication; 

negligence; alteration; accident; installation; neglect; misapplication; physical damage; fouling and/or scaling of the mem-

brane by minerals; sediment; bacterial attack; or operation contrary to our instructions, incompatibility with accessories not 

authorized for use with the system, or damage caused by freezing, flood, fire, or Act of God.

In no event shall Factory its subsidiaries or affiliates, or their respective officers, directors, employees, representatives, 

dealers or agents be liable for special, incidental, consequential, punitive, indirect, or other special damages, including but 

not limited to, loss of data, use, or profits, however caused, whether for breach of contract, negligence or otherwise, and 

whether or not Millennium® has been advised of the possibility of any such damages.

Factory assumes no warranty liability in connection with this reverse osmosis system other than that specified herein.  

This warranty is in lieu of all other warranties, expressed or implied, including warranties of fitness for a particular purpose. 

WARRANTY SERVICE:

Factory will provide warranty service under the following conditions:

1) 

Contact your local dealer who will obtain return authorization instructions.

2) 

Ship the unit or part freight prepaid for warranty evaluation or service with RMA # written on package. Systems or 

parts covered under the warranty shall be repaired (or, at our option replaced) and returned without charge.

CONDITIONS FOR OPERATION:

Operating Parameters:

Feed Pressure 

5-40psi

System Pressure 

60-100psi

Temperature 

4-38 C (39-100 F)

pH Range 

3.0 to 11.0

Maximum feed TDS level 

2000 ppm

Maximum Turbidity 

1.0 Net Turbidity (NTU)

Chemical Parameters:

Maximum Hardness 

350mg/L (20 gpg)

Maximum Iron (Fe) 

0.1 mg/L 

Maximum Manganese (Mn) 

0.05 mg/L

Maximum Hydrogen Sulfide (H2S) 

0.00 mg/L

Maximum Chlorine (Cl2) 

2.00 mg/L

Do not use the Millennium System on feedwater pressure above 40 psi. If feedwater pressure is above 40 psi, contact 

your local dealer for an alternative system not equipped with a booster pump.

Although TFC membranes are designed for non chlorinated feed supply, your Millennium

®

 RO system is equipped with 

double carbon pre-filtration for chlorine reduction prior to the TFC membrane.

Summary of Contents for new millenium

















Reviews: