WaterLogic Ecostream Manual Download Page 51

Page: 51 / 65

Ecostream

Manual

Page 51 - Revision: 11-13-2020

POWER TROUBLESHOOTING INDEX

Red Heater and Compressor Power Switch won't light

Red Power Switch is lit but No Hot and Cold Water

Compressor Runs but does Not Chill

Compressor is Not Running

Red Heater and Compressor Power Switch won’t light and the Red LED on
the Front won’t light

Possible Reason

Solution

Circuit Breaker

Check the Circuit Breaker

Fuse is Blown

Replace Fuse

Defective / Loose Power Cord

Check that power cord is properly plugged in. If it is properly

plugged in, use a different power cord to verify.

Failed Power Line Noise Filter,

ElectroMagnetic Interference

filter (EMI)

Replace Power Line Noise Filter, ElectroMagnetic Interference

filter (EMI)

Defective Red Heater /

Compressor Switch

Replace Red Heater / Compressor Switch

Summary of Contents for Ecostream


































































Search results

Summary of Contents for Ecostream

Reviews:

Related manuals for Ecostream

Brands by name

Popular brands

WaterLogic Ecostream, Manual

Search results

Summary of Contents for Ecostream

Reviews:

Related manuals for Ecostream

Brands by name

Popular brands