Wascomat EX-30 S and EX-50 S Operating & Maintenance Manual Download Page 76

Page: 76 / 88

Open door. Close door and try to restart the
machine.

Error code returns

No error code

Set program control unit to service mode (see
”To switch on service mode”). The door status
switch will now be indicated by the LED
(illustrated).

Press in the door status switch manually and
check if this is indicated by the LED.

LED does not light.

LED lights.

Disconnect the two wires from the switch. Short-
circuit the two wires.

LED does not light.

LED lights.

Remove connector X71 from the program control
unit PCB. Short-circuit between inputs 3 and 4.

LED does not light.

LED lights.

Trouble shooting

X71

2316

02E

Door status switch open
during program operation.

Check whether the pin on the
door or the plastic slide which
the pin presses against are
worn. Replace any worn
parts.

Continuity fault in wiring or
connectors. Check wiring and
replace if necessary.

Fault in program control unit
PCB. Replace PCB.

Short-
circuit

Door lock switch faulty.
Replace switch.

Cause/Action

Fault-finding

Error code/symptoms

Transient fault in door lock or
program PCB.

3430

LED
indicating

Door
status
switch

Summary of Contents for EX-30 S and EX-50 S

























































































Search results

Summary of Contents for EX-30 S and EX-50 S

Reviews:

Related manuals for EX-30 S and EX-50 S

Brands by name

Popular brands

Wascomat EX-30 S and EX-50 S, Operating & Maintenance Manual

Search results

Summary of Contents for EX-30 S and EX-50 S

Reviews:

Related manuals for EX-30 S and EX-50 S

Brands by name

Popular brands