Wascomat EX-30 S and EX-50 S Operating & Maintenance Manual Download Page 74

Page: 74 / 88

Error codes

Given below is a brief summary of all the error codes and their causes. Starting on page 5 of
this section there are fault-finding charts for all error codes.

At the end of the chapter there are also charts for faults which do not generate error codes.

Error code Cause

01E

Water level not reached within set time. Take necessary action. Press START again.

02E

Door status switch open during program operation. Take necessary action. Press
START again.

03E

The lock has not locked the door within the set time. Take necessary action. Press
START again.

04E

The temperature sensor indicates temperature below -5

C (open circuit).

05E

The temperature sensor indicates temperature above 98

C (short-circuit).

06E

The water level is above the safety level set for starting.

07E

The water level is above the safety level set for program operation.

08E

Temperature increase in water less than 5

C/10 min. (Heated machines).

10E

The water level is above the safety level set for after drain.

12E

The program control unit cannot read the program EPROM.

13E

Program control unit receiving no response from the motor control unit.

14E

Level system not temperature-calibrated. Press START to run the wash program.
Program will run, but the water level will not be optimally adjusted.

17E

Door status switch open, even though the door lock is locked.

43E

Unbalance switch on when motor not rotating.

45E

Tacho error

Trouble shooting

Summary of Contents for EX-30 S and EX-50 S

























































































Search results

Summary of Contents for EX-30 S and EX-50 S

Reviews:

Related manuals for EX-30 S and EX-50 S

Brands by name

Popular brands

Wascomat EX-30 S and EX-50 S, Operating & Maintenance Manual

Search results

Summary of Contents for EX-30 S and EX-50 S

Reviews:

Related manuals for EX-30 S and EX-50 S

Brands by name

Popular brands