background image

Warranty 

Warner Electric LLC warrants that it will repair or replace (whichever it deems advisable) any product 

manufactured and sold by it which proves to be defective in material or workmanship within a period of one (1) 

year from the date of original purchase for consumer, commercial or industrial use .

This warranty extends only to the original purchaser and is not transferable or assignable without Warner 

Electric LLC’s prior consent .

Warranty service can be obtained in the U .S .A . by returning any defective product, transportation charges 

prepaid, to the appropriate Warner Electric LLC factory . Additional warranty information may be obtained by 

writing the Customer Satisfaction Department, Warner Electric LLC, 449 Gardner Street, South Beloit, Illinois 

61080, or by calling 815-389-3771 .

A purchase receipt or other proof of original purchase will be required before warranty service is rendered . If found 

defective under the terms of this warranty, repair or replacement will be made, without charge, together with a 

refund for transportation costs . If found not to be defective, you will be notified and, with your consent, the item 

will be repaired or replaced  and returned to you at your expense .

This warranty covers normal use and does not cover damage or defect which results from alteration, accident, 

neglect, or improper installation, operation, or maintenance .

Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not 

apply to you .

Warner Electric LLC’s obligation under this warranty is limited to the repair or replacement of the defective 

product and in no event shall Warner Electric LLC be liable for consequential, indirect, or incidental damages 

of any kind incurred by reason of the manufacture, sale or use of any defective product . Warner Electric LLC 

neither assumes nor authorizes any other person to give any other warranty or to assume any other obligation 

or liability on its behalf .

WITH RESPECT TO CONSUMER USE OF THE PRODUCT, ANY IMPLIED WARRANTIES WHICH THE 

CONSUMER MAY HAVE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL 

CONSUMER PURCHASE . WITH RESPECT TO COMMERCIAL AND INDUSTRIAL USES OF THE PRODUCT, 

THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES, WHETHER 

EXPRESSED OR IMPLIED BY OPERATION OF LAW OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, 

ANY IMPLIED WARRANTIES OF  

MERCHANTABILITY OR FITNESS .

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above 

limitation or exclusion may not apply to you . This warranty gives you specific legal rights and you may also have 

other rights which vary from state to state .

Changes in Dimensions and Specifications

 

All dimensions and specifications shown in Warner Electric catalogs are subject to change without notice . 

Weights do not include weight of boxing for shipment . Certified prints will be furnished without charge on 

request to Warner Electric .

www.altramotion.com

An 

Altra Industrial Motion

 Company

P-0204-WE    8189-0485   5/17    Printed in USA 

www.warnerelectric.com

31 Industrial Park Road

New Hartford, CT 06057

815-389-3771

Fax: 815-389-2582

Send Quote Requests to [email protected]

Call +1(800)985-6929 To Order or Order Online At Warnerelectricparts.com

Send Quote Requests to [email protected] 

Call +1(800)985-6929 To Order or Order Online At Warnerelectricparts.com

Summary of Contents for PB-500 Pin Drive

























Reviews: