WAGO 750-486/040-000 Manual Download Page 66

Page: 66 / 102

Commissioning

WAGO-I/O-SYSTEM 750 XTR

750-486/040-000 4AI 0/4-20mA NE43 Ex i XTR

Manual

Version 1.0.0

Table 38:

Module settings

Menu Item

Option

Description

Noise Filter

Noise filter on



The noise filter is deactivated.



The noise filter is activated.

Watchdog Timer

Deactivate
watchdog timer



The watchdog timer is activated.



The watchdog timer is deactivated.

The green LEDs illuminate continuously.

Process value format

Display Mode

Two's complement representation

Amount/Sign representation

Factory setting

7.1.1.4.2 “Channel settings” Menu Item

Save settings!

Click the

[Write]

[Write all

]

button to write any settings you have made to the

I/O module.

Summary of Contents for 750-486/040-000







































































































Search results

Summary of Contents for 750-486/040-000

Reviews:

Related manuals for 750-486/040-000

Brands by name

Popular brands

WAGO 750-486/040-000, Manual

Search results

Summary of Contents for 750-486/040-000

Reviews:

Related manuals for 750-486/040-000

Brands by name

Popular brands