WAGO 750-486/040-000 Manual Download Page 4

Page: 4 / 102

Table of Contents

WAGO-I/O-SYSTEM 750 XTR

750-486/040-000 4AI 0/4-20mA NE43 Ex i XTR

Manual

Version 1.0.0

4.3.3.1

Sensor Type “0-20 mA” ............................................................... 42

4.3.3.2

Sensor Type “4-20 mA” ............................................................... 43

4.3.3.3

Sensor Typ “3,6-21 mA” (NAMUR NE43) .................................... 44

Mounting .................................................................................................. 45

5.1

Mounting Sequence .............................................................................. 45

5.2

Inserting and Removing Devices .......................................................... 46

5.2.1

Inserting the I/O Module ................................................................... 46

5.2.2

Removing the I/O Module ................................................................ 47

Connect Devices ..................................................................................... 48

6.1

Connecting a Conductor to the CAGE CLAMP

................................... 48

6.2

Power Supply Concept ......................................................................... 49

6.2.1

Supplementary Power Supply Regulations ...................................... 52

6.3

Connection Examples ........................................................................... 55

Commissioning ....................................................................................... 57

7.1

Parameterization with WAGO-I/O-

CHECK

............................................ 57

7.1.1

Parameterization Dialog ................................................................... 59

7.1.1.1

Title Bar ....................................................................................... 60

7.1.1.2

Main Menu .................................................................................. 60

7.1.1.3

Horizontal Tab Menu ................................................................... 61

7.1.1.3.1

”File” Tab ................................................................................ 61

7.1.1.3.1.1

“Open” Menu Item .............................................................. 62

7.1.1.3.1.2

“Save” Menu Item ............................................................... 63

7.1.1.3.2

“Start” Tab............................................................................... 63

7.1.1.3.3

“Connection” Tab .................................................................... 64

7.1.1.4

Vertical Tab Menu ....................................................................... 64

7.1.1.4.1

“Module settings” Menu Item ................................................... 65

7.1.1.4.2

“Channel settings” Menu Item ................................................. 66

7.1.1.4.3

“Scaling” Menu Item ................................................................ 69

7.1.1.4.4

“Calibration” Menu Item........................................................... 71

7.1.1.4.5

“Monitoring” Menu Item ........................................................... 74

7.1.1.4.6

“Information” Menu Item .......................................................... 75

7.1.1.5

Application Area .......................................................................... 76

7.1.1.6

Status Messages ......................................................................... 76

7.1.1.7

Status Bar ................................................................................... 77

7.2

Calibrating Measured Values ................................................................ 78

7.2.1

Example of Determining Gain and Offset ......................................... 79

7.3

Scaling Measured Values ..................................................................... 80

Diagnostics.............................................................................................. 81

8.1

I/O Module Behavior in the Event of an Error ........................................ 81

Use in Hazardous Environments ........................................................... 84

9.1

Marking Configuration Examples .......................................................... 85

9.1.1

Marking for Europe According to ATEX and IECEx .......................... 85

9.1.2

Marking for America (NEC) and Canada (CEC) ............................... 89

9.2

Installation Regulations......................................................................... 92

9.2.1

Special Notes Regarding Explosion Protection ................................ 92

9.2.2

Special Notes Regarding ANSI/ISA Ex ............................................ 94

Summary of Contents for 750-486/040-000







































































































Search results

Summary of Contents for 750-486/040-000

Reviews:

Related manuals for 750-486/040-000

Brands by name

Popular brands

WAGO 750-486/040-000, Manual

Search results

Summary of Contents for 750-486/040-000

Reviews:

Related manuals for 750-486/040-000

Brands by name

Popular brands